350 - Duals or single?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Nov 6, 2004
Threads
123
Messages
859
Location
Lodge Grass, Montana
The PO ran dual glasspacks out each side - flattened the pipe something horrid - the 350 sounds like a VW bug - so, should I go duals that exit in front of the rear wheels? or run a Y pipe and single all the way back - I want about 2" to the exhaust to maintain torque - then 3" on out the back on a single....or 2" to Magnaflows on either side? What would you do and why?
 
Frieght, unless you like the noise stay with the duals out the side, they also get in the way if they exit in front of the rear tire. Go with a signle that exits in the rear.
 
That is what I was thinking - the guy said that fabing the Y pipe is not a problem - I hate the noise/exhaust smell/and heat from the duals on the side right now -

Thanks -
 
ramshorns manifolds, $50 on EBay
SBC exhaust crossover - order from '66 1/2 ton Chevy w/283, $40-50
Hooker chambered muffler, $80 IIRC
2-1/2" single custom bent down the DS, $120

smooth....
 
woody said:
ramshorns manifolds, $50 on EBay
SBC exhaust crossover - order from '66 1/2 ton Chevy w/283, $40-50
Hooker chambered muffler, $80 IIRC
2-1/2" single custom bent down the DS, $120

smooth....


... and pushes a U-Haul like nobodies business!

If all you wish for is torque then your headaches and cost are best controlled using a single.

Like mentioned, exit out the side - not the back - behind the rear wheel.

Rice
 
I like the single pipe all the way back on my 40. I've got block hugger headers, then 2 1/4 pipe that goes to a Y pipe just below the drivers seat and then 3" pipe through a Flowmaster 40 series muffler, then it exits right behind the left rear wheel.
The whole system runs above the skid plate and is out of the way of everything.
The big plus is the sound, its cool.
 
what woody said i am in the process right now to switching to single exhaust . i ran duals forever .
but the pipes where always in the way . everytime i did anything with the tranny . t-case always hit the pipes so i'm chucking the duals see my dual setup in pic . i also had a bodylift . exited out behind the wheels
13 (Custom).webp
 
VTFJ40 said:
I just ordered a 70 series flowmaster. Supposed to be quieter. Which series are you using?

40 series. I think a 70 would be better. I like to hear what's going on with my engine and not just exhaust roar.

Freightdog - I am here at your service. :D
 
Gumby said:
40 series. I think a 70 would be better. I like to hear what's going on with my engine and not just exhaust roar.

Freightdog - I am here at your service. :D


I agree. I run dual 40's and they're a bit too loud. My exhaust guy "said" the 50's wouldn't fit with my setup and I'm still kicking myself for not taking it someplace else.
 
My Plan

I Currently have the fenderwell exit headers and two turbo mufflers, they look like hell and are barley on there from the light wheeling that i have done..

My plan is to run the Ramshorn 2" and possibly use the Chevy Y Crosover, then go to a single 3" down the driver side, Tucked up away from rocks.. Single Flowmaster or somthing above the rear axle and then exits out the back corner to reduce exhaust whirling back in my face with the top off..

my theory the 2- 2" = 1"(radius)(Squared)*3.14(Pi)*2(both banks) Yealds 6.28 (Area)
and the 3" yealds 1.5"(Radius)(Squared)*3.14(pi) means 7.06 (area)
2.5 would be 1.25"(Radius)(Squared)*3.14(pi) means 4.9 (Area)
If my Freshman Geometry is Correct, LOL, i would think a 2.5 would choke out the 2 - 2" pipes, where the 3" would open it up a bit, but not too much
 
Thanks all -

Woody - makes sense -

Gumby - think the 70 series is a good idea - i have one on the 60 and it is really quiet....I too like to hear my engine -

Isotel - I write grants for a living - so thanks for the geometry lesson - s*** -

PBGbottle - nice pic!

Yep, looks like a 70 / single / 2" to the 70 then 3" on back...
 
had a performance muffler shop do mine up...single 2 1/2" to magnaflow splitting into dual exits...this was their recommendation (except the muffler model...i asked for one that was quiet at idle, but spoke up when i jumped on it). works great.
 
I'm running a setup That I have really come to like. Block hugger headers into 2.5 inch tube. Snake the passenger side under and over to join the driver side, but keep both 2.5 inch pipes. I use baffles which fit inside the pipe rather than traditional mufflers. This means no clearance problems (from the outside it looks like straight 2.5 inch pipe all the way back). I run the tubes side by side and have an equalizer tub ahead of the baffles. This really helps both flow and noise levels. Great flow (almost as high as a straight pipe. It is as quiet as most high flow mufflers at speed, but is actually louder (subjectively) at idle and low speeds because the baffles do not provide enough restriction to cause the gases to back up and blend the pulses together. A very sharp crackle/bark at idle, much like open headers, but not as loud. It smooths out as soon as the rpm comes up and quiets. The dual 2.5 inch pipes give me more flow than a single 3 inch pipe (roughly 9.8 inches of cross section compared to roughly 7.1) and it are easier to fit under the rig.
If you have a full exhaust system you have more than enough bck pressure. Lack of back pressure affecting low end efficiency is a concern when running lareg tube open headers at the drag strip. Not in any of the rigs we deal with here running rams horn or block hugger headers and pipes/mufflers of any diameter..
 
Back
Top Bottom