3 Spd T Case Bench Test ?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 9, 2004
Threads
386
Messages
3,997
Location
Montgomery Co. TEXAS
Website
missionsonwheels.org
What is the best way to bench test a vacuum T Case shifter, the part mounted on the front output housing. It seems very hard to move by hand and want to make sure it will work once I install the case.

Thanks, Mike
 
You should be able to shift it by attaching a hose to one side or the other and blowing or sucking on it, with your mouth.
 
I sorta tried that but didn't really want to mention that...kinda sounded :princess: . I can;t move enough air through it to actuate it. I did manage to get broke free so it will move and I think the billows inside are okay, judging by the vacuum & pressure buildup. How much vacuum does a 2F generate? All my junks sitting on the floor but I can get a vacuum tester Monday and try to move the shifter at a normal 2F vacuum.

Floor shifter isn't really an option for me right now, besides I sorta like 'shift-on-the-fly' feature.

Mike
 
IDave said:
You should be able to shift it by attaching a hose to one side or the other and blowing or sucking on it, with your mouth.

yep,
this will actuate a properly working and maintained vacuum shifter. Forward port pulls it into 4wd, rear pulls it into 2wd when you apply vacuum to it IIRC

I havent figured out why people dont like the vacuum shift. they work well if you spend $15 on a new diapraghm, and $10 or so on the vacuum transfer soleniod rebuild kit. Update some vacuum hose and they are pretty damn reliable.
 
Forget about the vaccum and get a floor shifter. Unless your restoring the vehicle.

I also have a vacuum shifter and think it's great. Is there any reason or situation where a floor shifter is better :confused:

In 6 years, I never had problem with it.
 
froggy said:
I also have a vacuum shifter and think it's great. Is there any reason or situation where a floor shifter is better :confused:

In 6 years, I never had problem with it.

My first Cruiser had the vacuum shifter, and for the most part it was great, but one time without warning it put an early end to a wheeling trip. I tend to prefer as simple as possible, and it doesn't get any more simple than a lever. Even if the linkage breaks, you can still get by.
 
froggy said:
I also have a vacuum shifter and think it's great. Is there any reason or situation where a floor shifter is better :confused:

In 6 years, I never had problem with it.

No.
The floor lever is direct, so I guess you have a bit less chance of failure, but the nice aspect of vacuum is to select 2wd or 4wd and thats it, it will shift once everything is aligned. Whereas the direct style needs to be shifted when there is no load on it, so you might have to fiddle with it to get out of or into 4wd.

as long as you periodically shift the vacuum shifter, they are fine... you might have to rebuild the little solenoid box thing, but the kit from toyota is cheap. I like the vacuum shift.
 
66fj40 said:
How much vacuum does a 2F generate? Mike

Normal vacuum is 16-20 (well, 18) inches of Hg.
 
IDave said:
Normal vacuum is 16-20 (well, 18) inches of Hg.
Thanks for the help IDave.

I've never had a reason to switch to a floor shifter either. I've owned the rig for 5 years and been wheel'n for 4 now without an incident. It's been very handy on trails and never grinds a gear.

V-DAWG, what broke to end the trip?

I should probably through a rebuild kit in mine at some point, but it just keeps going.
 
Take the vacuum shifter apart, clean and reassemble, and chances are it will outlast the rest of the truck!

Good stuff.

BTW, CDan's should have the part numbers handy. :)
 
Back
Top Bottom