3 spd column shift parts?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Nov 9, 2004
Threads
13
Messages
25
Ive got a 1971 fj40 that still has the 3 spd on the column. Everything works except Im missing something that connects the shift rod to the blinker assembly. The only thing I can figure is hat there is a threaded tube or something with a 10mm threaded inside and a little bit bigger on the outside. I have tried threading a helicoil between the two but had no luck. I have also tried looking for the part in just about every parts place/wrecking yard I can think of locally. I talked to the toyota guy at the dealership and we looked at several illustrated diagrams and it didnt show up on any of them. Does anybody know how these two parts connect, and if there is something I am missing do you know where to get it or is there at least a part number? I have a three speed floor shift with a manual (non vacuum case) that I really dont want to put in. It looks good now, it just doesnt quite work. Any help would be greatly appreciated. Thanks, Mike
 
If you can, take a picture of that area you are talking about which has the missing piece. I'm not sure I follow your description. I probably have an extra of what you are talking about, but I'm not sure what you are referring to precisely. The turn signal lever works independantly of the column shift (my column shift 45 was [temporarily :cool: ] converted to floorshift and retains the original turn signal switch).
 
As I recall, there is a cast metal piece just below the steering wheel that supports the upper ends of both the shifter linkage and the turn signal rods (at least on my 64).

From what I am envisioning, you're looking for part "G" in the following diagram.
056B1.gif


It threads into the piece below the steering wheel, and sticks into the shifter shaft about an inch and a half. It has no 'bolt head' - it's just smooth except for a hole in the end. I removed mine by pulling out the shift lever and (with the shifter linkags disconnected) sticking a screwdriver into the hole to unthread it 1/2 turn at a time.

Hope that makes sense.
 
I am cunfused, the shifter has nothing to do with the turn signals..........
 
Landpimp said:
I am cunfused, the shifter has nothing to do with the turn signals..........

They both have their upper ends supported by the same chunk of metal below the steering wheel on the column - just on opposite sides. I assume that's what he's talking about.
 
The column shift does have a pin that goes into that hole in the turn signal switch. It is not necessary for the turn signal, because the surround clamps onto the column on its own. However, I think that in order to keep the column shifter centered, you do need the shifter pin inside the hole in the flasher switch. If somehow that brass piece in the hole is missing, the switch won't support the column shift.


I do have an old switch with a broken arm that has the centering thing intact. The switches can be pulled apart and reassembled (rebuilt, so to speak). So if you want that old switch housing, let me know!
 
there's a cone shaped piece that g goes into and on the side is where the piece sticks out that the rod for the t/s's goes to..., but g has nothing to do with the t/s's
 
I just spent a couple of hours looking at a couple of three speeds that were in some cruiser guys boneyard (way cool 2 45 wagons, and a 40 on rockwells and 49"s... Im 6'3" and the running board was at my shoulder. not for sale but those things are sweet) Unfortunately it looks like there is no piece that goes between the two. In the exploded diagram that e rock posted I am looking to see how part G attaches to the turn signal housing. The ones I looked at today that are functional had nothing other than "part G" and the turn signal housing. I have two turn signal housings but the threads on "g" are smaller than the threaded portion on the housing where it is supposed to attach. I think I am going to put my booty fab skills to the test and try and make a new part "G" out of a 10 mm bolt with a shoulder on it and attempt to make a shim that will hold it tight within the column. Hopefully that makes sense. I can visualize stuff way better than explain it. The guy also had a Specter catalogue, although I will probably buy nothing out of it its diagrams beat the hell out of a chiltons.
 
nuclearmon, would you happen to have a pic of the cone shaped piece? The best I can describe what I think that I am looking for is a sleeve that goes over the threads on part G
 
74k5 said:
nuclearmon, would you happen to have a pic of the cone shaped piece? The best I can describe what I think that I am looking for is a sleeve that goes over the threads on part G
here's the back side of my steering wheel. the empty hole at the top is where the shift rod used to be (i'm now floorshift 4spd). the rod on the left side (sitting in the vehicle...right in the picture) is the turn signal rod.
P1200118.webp
 
You cannot use a 10mm bolt to replace G because the shift lever for the column shift pivots off of G as it moves the main rod [parallel to the steering shaft] up and down. G basically screws into the turn signal bracket the way Ige explained it and floats loosely, rotating back and forth on the threads as the gears are shifted. Eventually the threaded pot metal of the bracket wears down, causing your problem.

What you need to be looking for is just a turn signal bracket [the upper one] that your "G" will fit into. If you buy a new turn signal switch from the dealer, the bracket will come with it. ;)
 
I talked with Mike (74K5) after he left the shop tonight and apparently after he posted his last message. Sounds like he got it all working okay.

The part he ws dealing with was infact the "G" in the diagram posted here. SOunds like there was smoe misunderstanding about how it was supposed to fit 'cause he said on the phone that it all went together fine. His "G" was siezed in the shifter column and he didn't realize thatit cam out and had a spring underneath.

Some of these do rotate back and forth with the threads spinning in the collar. But they are not supposed to. "G" is supposed to be fixed and the column is supposed to rotate around it. The wear in the threaded section is not supposed to occur. After years of use and abuse however sometimes "G" siezes in the shaft.


By the way, Mike... The '40 on Rockwells is sitting on 53s not 49s. The tires in the yard beside the 45 LWB were 49s. ;)
 
My shifter on the 71 was crap, swap it for a floor shift and be done with it. It's a easy conversion and you will like it alot more. just my .02
 
Hey, it works now... It all bolted together just like it should. Thanks to everybody for the help, and Mark, sorry about the confusion... Friggin huge would have been a better choice of words regardless though that thing is too damn cool.
 
'sokay... Didn't hurt my feelings, just nitpicking. ;)

It'll be cooler once it is back on the trail and no longer gathering dust in the shop. :(
 
As they say in the US Senate, I must respectfully disagree with my esteemed collegue.

While you can control the position that a bolt or a machine screw ends up in if you can rotate the nut on the backside of a plate, when the threaded destination of the screw is preset or welded in place, you cannot control with 100% accuracy where the screw will finally tighten down.

While I have every reason to believe that Toyota used their best efforts to cast the turn signal bracket so that G would end up in the correct position, I do not believe the hole was threaded 100% accurately. I also do not believe that the column shift lever can make it's complete up and down sweep without 'G' following it, which necessitates rotating.

The fact that Mike's 'G' was frozen in his column confirms that the column was functioning with G following the stick shift lever, not fixed to the turn signal bracket.
 
G was turning in the shift rod (J) i still dont fully understand the problem because the threaded part of G woul dactually slide freely into the threaded portion of the turn signal housing but when I took G out of the column after seeing in the diagram that it was a seperate piece independant from the lower portion of J it bolted into the threaded portion of the turn signal housing that it slid into before (imagine trying to thread a 9mm bolt(g) into a 10mm nut(turn signal housing)... it doesnt work) I am still confused as to why it did that in the first place, it physically shouldnt work, but it does. As far as the threaded portion not being perfect, I used my dremel tool on the turn signal housing and now it seats tight with no slop. Hopefully that will alleviate the problem of it wearing out again.
 
You might be right about "G" needed to turn in the threads. I'd have to pull one apart and look at it to feel 100% certain. It has been a long time since I pulled one apart to do anything other than remove it when installing a floor shift., so as I sit here tired and late to go home, I won't try to make a difinitive statement.

If it is intended to rotate within the threads this seems to be a design flaw. Either that or I'm missing something.


Mark...
 
Back
Top Bottom