3-link progress pics from today

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Mar 20, 2006
Threads
381
Messages
1,821
Location
elkcreek canyon colorado
Got the 3 link all tacked in place today, SLOWLY but surley!
IMG_2795.webp
IMG_2797.webp
IMG_2798.webp
 
I thought you had giving this project up, when you were on your 80 series parts selling spree.
 
The pics make the tower look way taller than it is, I was embarasssed to take any closer pics due to the greasy frame from the old engine and steering box:o. Now that she is a roller, I can push her outside and degrease/pressure wash the frame rails and take much better pics. It is getting a SBC, have not decided between an LT1 or TBI yet (fuel consumption being the biggest determining factor at this point, big difference between 10 and 15mpg with the fuel $$$ now:rolleyes:) It is getting an 01' internal slave GM NV4500 mated to a late fj60 case, thinking of using a T100 clutch pedal and master setup. I was going to abort mission on this a while back and sold all the adapters and 05' GM 6.0/tranny but could NOT sell the truck for $1000!!!!!!!! so I decided to finish it in my spare time. Now I am kinda glad I kept it, she should be a cool multi-use truck when finished. More pics soon.
 
cool project. The tbi will be so much easier to wire I'd immagine. id rather have the 4500 than the auto you gave up. keep it going. good luck on the spare time thing-im struglin with that one myself.

I know this is going to take some time but throw us a bone and post a pile of 3 link pics. lets see your brackets, links, etc. share your thoughts on the design you chose and why. what are your links made from? how long are they? did you move the axle forward? how much lift you running? etc etc

Your upper link looks tall but you placed your lower axle links relatively high making the need for a high upper link. what is the verticle seperation between the upper and lower links?

Subscribed
 
Good proyect .. good to se the NV4500 in a 80 series, much more with a 60 t-case .. luck with a low gear set !
 
The vertical distance between the lower control arm mount and the tower mount is 10", the upper link is 25" and the lowers are 35.5". One challange will be getting the the SBC pushed back far enough so the NV4500 shifter does not come up too far forward under the dash. I like the idea of the TBI because for $350 and 1hr of wiring your done, but the tpi/LT1 would get 4-5 MPG better I think. It has 5:29's in it already.
 
92 and 93 factory LT1's had distributor issues. The slotted disk kept rusting due to moisture and the optical pickup would throw a code and shud down the ignition. There was a recall I believe. There has been aftermarket progress as well to get this to be more reliable. My 92 went out 3 times in 2 years. I sold it!! I had it in a 89 s-15 4wd. Now its in a 70 nova. He did an aftermarket upgrade and has only replaced it once in 2 years.
 
Ya, I heard they earned the name opti-crap from those years. Just thinking out loud, I may be able to push the motor back a little fruther without a dizzy in the rear? Therefore, putting the shift tower on the tranny closer to where I want it. But the heads may be more of a limiting factor since the 80 has a recessed center in the firewall anyway.
 
If you havent bought an engine yet and are worried about MPG why not go with am LSx? 5.3 would move it fine and prob get more than 15mpg.
 
yaa I for one would be real curious as to how you are calcing the numbers?

anti squat etc.............

mine needs some minor correction when I get time to work on it.
 
.120 wall DOM arms. The arm lengths are listed above. As for the "anti-squat" qestion, do you mean preload? The Johny joints have a lot of thread, should be plenty of adjustability. It is very similar to action jackson's setup with just slightly longer arms and different frame mounts, more pics to come!
 
as for anti squat, not trying to educate you cause i'm no pro at all, but when developing the geometry of the linkage, if your angles are not "right" then the rear axle tries to walk under the truck during acceleration causing it to raise the rear up every time you hit the gas.
 
moto, you might want to consider going thicker on that tubing if you intend on wheeling it at all (if it's not too late). I am using 2"OD x .25 wall.
 
Back
Top Bottom