2F or CSB engine??

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jun 26, 2006
Threads
111
Messages
293
Location
Longview, Texas
I am new mud member and have posted a few threads over the last two week. Have been writing about questions regarding my new 74/40. It has a 283 that po installed. Looks like it will require a complete rebuild to get running...but I expected that when I purchased due to amount of time rig sat up. I would like some of your opinions as to whether I should go back with SBC or find a 2F to install.

PO did some really hack mods to get the SBC installed. Welded angle iron to frame and mounted motor mounts to welded bracket. Also removed original tranny cross member and welded 3" channel iron to mount tranny... Both of these mods look like s---, but probably do the job. I would like to make what ever I do look better under the hood too.

Also, the current sits at a good angle sloping front to back. PO did this so oil pan would clear exhaust pipe coming from left bank. Guess this doesn't hurt, but normally I thought enginge should sit fairly level. So to go back with 2F, I would have to "undo" what po fab up. Probably not too hard but will take some work.

If I go back with SBC, what size...rebuild 283 (if block is decent ..don't really know yet) or go with different 350????

What I think I want is a 2F and upgrade to a 4sp tranny. Don't know really why other than to just go back to original..Now I don't have available a 2F that is ready to drop in, but I am going to look at a 78/40 next week sometime. Supposedly very rough, but is running. However, po says engine has spun a bearing and overheats. This may be a good rig for parts depending on condition. I am certain I can buy for < $1000, but not firm on price. Tranny and t/c is problably good. What is average price to buy complete rebuild kit for 2F. Rebuilding this 2F is an option.

I also know a guy locally who removed another 2F in the mid-80's from his 78/40 and has enginge stored in shop. It is complete even with toy bell housing. All that is missing is altenator. It has approx. 60K original miles and ran strong when he removed...maybe burned a little oil he said. The only thing he did not do when he stored was oil cylinders.

Not sure of the condition of this engine being stored for 20 years inside. What would be fair price for this engine...he mentioned $700, but I think that is high..thinking more of $500 range. I feel certain this is probably the better engine of the two.

I want this cruiser to be mechanically sound, look good and a dd. Will drive to work with HT removed 9 months out of the year and also be used as dog training vehicle. Not a lot of heavy mudding or rock crawling.

Sorry for such a long thread.. but I would greatly appreciate some comments and opinions to help me decide.

Thanks...

dogman :confused:
 
Im in the same boat. Im in the process of replacing my 2F. MUD has been a huge help as youlle find the best deals. As far as I know, rebuilding 2F's tend to get pricey depending what you want and how much work you intend to do yourself. From what Ive gathered (Im new here too) your going to spend around 2-4k on a rebuild.

Your best bet is to find a good used engine (like the one youve already found) and do what youve got to do to fab the mounts. Thats if you decide to go the 2F route. $700 does seem high, $500 or less seems about right considering time its been sitting. Wait it out, and see what you can find off of MUD. Good luck

For instance:
https://forum.ih8mud.com/showthread.php?t=102600
 
Last edited:
It would probably be easier to fix some of the P.O.s mods up some and drop a new S.B.C. unless your going for a stock resto or something then it would be worth it to drop a 2F..

I think it would be cool to go with something that you don't see in a whole bunch of other L.C.s like a 327 that is if the 283 doesn't work out for ya..




Personaly I think a S.B.C. would be more friendly performance and economicaly wise than a 2F for a DD..


I remember there was a thread about 2F vs. S.B.C. but I couldn't find it in a search


:cheers:

-my64fj40
 
IMHO, it's going to cost you a mint to go back to a 2F, unless you have a donor vehicle, with frame, mounts, etc.

If you want a 2f, you'd be $$$s ahead to find another 40 that's unmolested.

If you want to keep this vehicle, just fix the PO's crappy work, and put in another SBC.

FWIW, I prefer the 2F for that tractor feel, but the SBCs are probably better daily drivers.

I'd never do an SBC conversion - it looks muy expensive to do it right!

Kirk
 
i had a 327 out of a corvette in my land cruiser i got from work(work at a chevy dealership as a tech) and i took it out and put back in the 2F motor cause i love the straight 6! if you lived in oregon id have a well built motor for you with everything you need to get it started but its really up to you... if you go with a 2F motor id recomend changing the transmission out let me tell you there no fun at 60-65 mph :frown:
 
Slight hijack -- still dealing with motors for a 40 though

crazylandcruiser -- your previous post caught my attention. I have a some questions for you if you are willing/able to help answer them. Where in Oregon are you located? Since you work at a chevy dealership, are you familiar with the GM straight 6 motors? If so, I am looking for some technical info on them.

OK -- hijack over
 
my64fj40 said:
It would probably be easier to fix some of the P.O.s mods up some and drop a new S.B.C. unless your going for a stock resto or something then it would be worth it to drop a 2F..

I think it would be cool to go with something that you don't see in a whole bunch of other L.C.s like a 327 that is if the 283 doesn't work out for ya..




Personaly I think a S.B.C. would be more friendly performance and economicaly wise than a 2F for a DD..


I remember there was a thread about 2F vs. S.B.C. but I couldn't find it in a search


:cheers:

-my64fj40

Is this the thread you were looking for?

https://forum.ih8mud.com/showthread.php?t=74640

Go the 2F:D
 
Back
Top Bottom