HEI. What do I need?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Feb 15, 2005
Threads
2
Messages
26
Location
colorado
I would like to convert my FJ60 to HEI. I could go down the street and just buy the ready to bolt in distributor for $295 but I would like to save some $ and do it myself. As I understand all I need is a HEI distibutor from a chevy V6. Than I have to machine the distibutor housing to fit in the toyota block, and change the gear on the shaft to the toyota gear? Is my information correct? What year and make chevy shuold I look for at the wrecking yard for the distributor? Any help would be appreciated.
 
why do you want to get rid of the stock fj60 dizzy? its a great unit and trouble free. I would never install a HEI/DUI on my Cruisers.
 
I can get the distibutor for under $50 and I have a lathe and a machinest at work to machine it for me for nothing. With a new cap rotor and wires I am sure I can do it for a lot less than $295 I have always been a chevy guy before I bought this thing and I guess old habits are hard to break.
 
you would need a diz from a straight 6, not a v...

i got mine from a 79 nova for 45 bucks. looked it over expecting to need a rebuild, but it was in great shape. switched gears and made sure i had the toyota gear far enough down the hei shaft so that it would still drive the oil pump (make double, triple, a lot of checks on that one....)

fabbed a new one piece bracket for the larger diameter chevy diz and tossed her in there....

got rid of the points and made me check my timing...actually gained a mpg, ha ha


malphrus
 
search for this and there are a couple pretty long threads as well as a write up in the tech section (that's what i used...abt 2 years ago, i guess it's still there)


malphrus
 
You do not want to use the VTV on the vacuum advance hose with the HEI dist or you will have knock problems.

Don't you have to recurve the advance from the checy to the LC?

I read that going with a nonUSA dist will give you the same results as the HEI dist, is this true?
 
landtoy80 said:
Don't you have to recurve the advance from the checy to the LC?

If you are going to modify from stock build you will need to match the distributor advance curve to the carb setup.

De-smog'ed carbs have ported vacuum advance available for the distributor while the stock carb's only have manifold advance.

Hence when you use a stock carb's manifold advance (VTV) for a distributor set for ported vacuum ... there's a heck of a lot of pinging going on ...

HTH,
Cahil
 
CATMECH said:
...
I think It's not advancing enough ...

Hmmm, well ... yeah.

If you did a *correct* carb de-smog you will need to get the distributor re-curved ... then probably install headers too ...

Once you start mod'ing from stock it gets complicated ... but do-able.

Cahil
 
OK! I went and checked some things on the cruiser. I checked that litttle check valve in the vaccum line between the carb advance port and the diz. The one thats black on 1 side and blue on the other, it was leaking so I pitched that and replaced with a straight hose. I dont know why I ever put that back in in the first place. That was definatly part of the problem. I took it for a cruise and it red lines quicker than before. I took it up a big hill on the highway and it gained 10mph faster than what it ususlly will do. So it is definatly better than it was. When you say get the diz recurved what exactly does that mean? I have never heard that term before.
 
CATMECH said:
When you say get the diz recurved what exactly does that mean?

As I understand ... it's modifying the internal weights/springs of the distributor to either increase or decrease the advance for a given rotation & vacuum.

HTH,
Cahil
 
landtoy80 said:
The VTV holds the vacuum advance too long for the HEI. Don't know about for a desmogged stock dist but its probly the same.


The second port on the dist (if I remember right) was for high altitude???


Ahhh ... didn't know that about the VTV.

Yup, second port is for HAC (high altitide compensation).

Usually it's 8 degrees for first port and 4 degrees for second port, IIRC.

On a side note I'm running a stock carb with mechanical advancing DUI HEI. Just fine for now. Eventually de-smog the carb, larger jets, and hook up the vacuum advance for the DUI. Next project. :rolleyes:

Also it's important to check your timing *fully* advanced. I check mine @ 3k rpm. I'm running ~ 28 degrees. My base timing is 2 degrees. In order to run more advance I'll need to run larger jets. Stock carb is to lean for the HEI.

Cahil
 
Last edited:
My base timing is set at 12deg, when I hook up the HAC port it advances to 16deg. I havnt checked what it is fully advanced yet but it didnt start pinging when climbing that hill. I will check it again later.
 
landtoy80 said:
You do not want to use the VTV on the vacuum advance hose with the HEI dist or you will have knock problems.
Actually, the VTV will reduce knock problems by slowing down the vac advance.

landtoy80 said:
Don't you have to recurve the advance from the checy to the LC?
Yes, two reasons. One, any HEI distributor is new enough that it is a smog calibrated unit. Two, any chevy engine w/ HEI has a more modern cam and bore/stroke profile that requires a very different curve than a Cruiser engine.

landtoy80 said:
I read that going with a nonUSA dist will give you the same results as the HEI dist, is this true?
No, not really. The typical non-smog distributor is a 64-67 USA points distributor. A copy of an old Delco distributor. Not a very good design.
The HEI is at least fully electronic.
 
CATMECH said:
OK you have convinced me to try to get the old distibutor to work right before I try the HEI. here is my situation. I have already desmogged the engine everything but the air pump. My question is, why is there 2 advance hook ups on the distributor. I have the 1 closest to the diz hoooked up to advance port coming off the carb. according to my diagram it originally ran through the VCV valve. The outside vaccum port on the diz I have going directly to manifold vaccum.

The two distributor vacuum fittings are advance. The primary advance is closest to the distributor body. It gives something like 22Deg crankshaft advance. That's a lot. The secondary advance (originally for hi-altitude) gives 6-7 degrees. First thing you should do is verify that both advancers are working. Use your hand vac pump and dial back timing light.

Don't connect the second advance to manifold vacuum, that just makes it fight the primary advance.

The thing is that the engine runs real good it just seems like on the highway when going up a hill it needs a little more advance on the timing. Yes I have checked the timing And it is actually set about 8deg advanced of the specs. But I live at 10,000ft altitude. It did help alot but I think It's not advancing enough. And yes I have made sure my secondary is opening on the carb.

I would suggest running a total of 43 degrees at 3700RPM at your altitude. You'll have to measure your current advance curves and calculate backwards to find the base timing setting.
 
cahilc said:
De-smog'ed carbs have ported vacuum advance available for the distributor while the stock carb's only have manifold advance.

Hence when you use a stock carb's manifold advance (VTV) for a distributor set for ported vacuum ... there's a heck of a lot of pinging going on ...
A carb does not have ported vacuum advance. It may have a ported vacuum fitting that can be used with a vacuum advance distributor.
And manifold advance? That's just not right, kinda like "muffler bearing". ;p

Most stock carbs (all FJ60 carbs) have a ported vacuum fitting that can be used with a vacuum advance distributor.

If there is spark knocking, then the timing is too early. It may be due to too much advance curve, or it could be the timing is not set right.
 
Back
Top Bottom