Recent content by twitchfury

  1. twitchfury

    Sputtering, loss of power - Case of Beer for the person solves! :)

    Also, I have no experience with the injectors, testing them, etc. Is this a home garage mechanic job or deeper?
  2. twitchfury

    Sputtering, loss of power - Case of Beer for the person solves! :)

    Thanks for this. How does one perform a smoke test?
  3. twitchfury

    Sputtering, loss of power - Case of Beer for the person solves! :)

    Hey guys! Need your help. 1993 FJZ80 - 275k Miles Until recently no issues until about a month ago, truck started rough idle, loss of power, and sputtering while cruising. After reading through the forum, I thoroughly cleaned the TB and MAF sensor, cleaned EGR, put it all back together, and...
  4. twitchfury

    Need advice on some Squeaky squeaky

    I’ve got a pronounced squeaking when I go backwards/reverse coming from what sounds like the passenger rear area. Hard to tell exactly. Replaced all the pads and front rotors. Replaced the parking brake shoes even though they looked fine. Replaced right front caliper, unrelated. Greased the...
  5. twitchfury

    Bed liner body: Results

    Did a little project over Father’s Day weekend and thought I’d share... Never had the maroon fenders, bought it without them. 1. Removed bumper and tail lights 2. Sanded, washed, scrubbed, washed 3. taped 4. Roll Herculiner, dab brush 5. Let first coat dry for 12 hours (mostly because it was...
  6. twitchfury

    In over my head...put on the brakes. Help!

    They have been ordered.
  7. twitchfury

    In over my head...put on the brakes. Help!

    Question for everyone...after I properly get these bearings tightened, should I replace this rotor, have it turned, or will it smooth back out on it's own?
  8. twitchfury

    In over my head...put on the brakes. Help!

    Ok, I did the check. There is a little bit of movement on both sides. Not much but a little bit. Should there be zero movement?
  9. twitchfury

    In over my head...put on the brakes. Help!

    Will do and report back! Thanks.
  10. twitchfury

    In over my head...put on the brakes. Help!

    I will give that a try. The only thing I can come up with is that the rotor is touching the inside of the caliper some times. Possibly when turning?
  11. twitchfury

    In over my head...put on the brakes. Help!

    Thanks. Just went and checked. Caliper bolt has plenty of clearance. I reused the existing bolts and bought a couple new from Toyota. Both the same.
  12. twitchfury

    In over my head...put on the brakes. Help!

    Could wheel bearings being loose cause this damage to the rotor?
  13. twitchfury

    In over my head...put on the brakes. Help!

    TBH I watched a YouTube video. Tighten, turn the wheel, tighten a bit more, turn the wheel back and forth, back it off a little. Repeat. Put on tire, hit it with a sledge. Turn the tire. Repeat process until bearings are set but not over tightened. Could the wheel bearings being loose cause this?
  14. twitchfury

    In over my head...put on the brakes. Help!

    Hey Guys. Background: 1993 Land Cruiser FJZ80 Two weeks ago I replaced my calipers, rotors (powerstop drilled/slotted), brake pads, and wheel bearings. The job went well, it was driving better than ever. Tracking straight on the highway and no pulling to the driver side (as it did previously)...
  15. twitchfury

    Check your caliper bolts!!

    Could driving 100 yards with one tire dragging damage any internal parts? Front knuckle or axel?
Back
Top Bottom