Recent content by taylorqj

  1. taylorqj

    Pirate the '88 FJ62 Build

    After replacing just about everything I can think of and some things twice, I found the culprit.. a burnt up, crusty, and somewhat working engine harness. I chased fuel pressure from the rail all the way to the tank, triple checked all spark, and made sure vacuum was good. I knew the harness...
  2. taylorqj

    1986 FJ60 - Custom 3D Printed Temp Sensor Gauge with ESP32-S3 and Arduino Code for Coolant Temp

    Super cool, thanks for sharing. I've been thinking about building something similar for under the gauge clusters of a 62.. a panel to show fuel/oil pressure, coolant temps, and voltage. I have none of the electrical experience but a ton of the software experience.. and have had my fair share of...
  3. taylorqj

    Pirate the '88 FJ62 Build

    Not impossible but I’ve tried both the old and the new one. Worth another test.
  4. taylorqj

    Pirate the '88 FJ62 Build

    This build has quickly turned into fixing issues rather than building.. at least we’re refreshing parts. I dropped the tank and replaced the fuel pump + refreshed the tank hoses with a kit from @cruisermatt (thanks dude!) Unfortunately still having the same issue, it does seem less...
  5. taylorqj

    Pirate the '88 FJ62 Build

    I think I have narrowed it down to the fuel pump, which is funny, as it was "working properly" before I started replacing all the fueling parts. Tried ordering the LCE Fuel Pressure Bolt Kit but fulfillment was taking forever so I picked up a Maddox fuel injection service kit at HF that includes...
  6. taylorqj

    Pirate the '88 FJ62 Build

    @diesellibrarian I set timing per your recommendation and my idle dropped to a still-not-normal 800~ which is much better than 1100-1200! I’ll be doing valves soon. Maybe a slight change in the stumbling, bogging, and backfiring.. less pronounced but still happening. Thank you. I went through...
  7. taylorqj

    NE SAS #10 Convoy

    I might be interested assuming I get my 60 together
  8. taylorqj

    Road trippin in the 60 series

    Couldn’t agree more on the viewing angles of a 60. Cool truck
  9. taylorqj

    Pirate the '88 FJ62 Build

    Everything is back together and running.. but not running well. I’m bogging, stuttering, and backfiring when giving any amount of gas while in gear. Park and neutral I can freely rev without any choking. I’m able to lightly give gas and feel constant pressure through the pedal until about 1.5-2K...
  10. taylorqj

    Pirate the '88 FJ62 Build

    I wanted to keep working on things while the injectors are getting rebuilt so I decided to replace spark plugs, o2 sensors, and do a hack-job painting the airbox. The o2 sensors connector nearest to the driver side (non trans) looks like it’s been cooked a bit. Luckily just the sensor side and...
  11. taylorqj

    Pirate the '88 FJ62 Build

    Picked up a breaker bar and a pipe.. took a lot of work but it broke loose.. that sucker was in there. I was debating pulling the exhaust manifold while I wait for parts.. but not so sure now, lol. I’ll likely hold onto the smog stuff for a little bit just to see how the truck runs, there’s...
  12. taylorqj

    Pirate the '88 FJ62 Build

    I’m still awaiting parts so still poking around and doing a thing or two here and there. Continuing with the desmog.. I’ve soaked that dang EGR exhaust nut for days and it will not budge. I’m half tempted to pick up a 1/2 impact and give that a go.. makes me wonder though.. why not just cap...
  13. taylorqj

    Pirate the '88 FJ62 Build

    Thank you! My wife has definitely commented on the amount of boxes arriving to the house almost daily. Cool to hear you had a similar one, I really like the tan and stock bits.. it’s going to be hard to change but we’ll see where the truck goes. Too early to tell. Just need to push the reset...
  14. taylorqj

    Pirate the '88 FJ62 Build

    Picked up a Mountain Hatch tailgate cover from @cruiserpatch (thanks dude!) I had one on my Tundra and it was nice to have a useable service for cutting food and not worrying about dragging things across the tailgate. Maybe I'll get around to a storage mod some day, but this should work well...
  15. taylorqj

    Pirate the '88 FJ62 Build

    Hey thanks, it's definitely a solid rig. Not a ton of rust and was previously someone's daily. Good idea on injectors, I was intending to have them cleaned up and tested rather than buying new if I could help it. I've heard good things about Mr. Injector on here.
Back
Top Bottom