Recent content by SoCalBruiser

  1. SoCalBruiser

    1991 Land Cruiser Code 25 and 26 after rebuild

    1000 miles later, still resolved. No CEL and exhaust passed CA emissions as good as a new car (according to the technician).
  2. SoCalBruiser

    1991 Land Cruiser Code 25 and 26 after rebuild

    RESOLVED! Thanks everyone! I think this is finally resolved (pending a smog check). After replacing just about everything, save the injectors, I went ahead and replaced the injectors. I had installed Beck Arnley 158-05 80 injectors a couple years ago that ran fine before the rebuild. After...
  3. SoCalBruiser

    looking for help with my FJ80 3FE, built 3/1992, CA emissions check engine codes 25, 26, and 71, 356,000 miles

    Mine turned out to be failed (leaky) fuel injectors. I found gas in the runners when I took the intake off - dead giveaway.
  4. SoCalBruiser

    1991 Land Cruiser Code 25 and 26 after rebuild

    Thanks for sticking through the long posts! At this stage I'm stumped on why both VF1/E1 and VF2/E1 would be showing the exact same data through all these tests. I have to imagine given the descriptions in the FSM that VF1 and VF2 give you independent feedback voltages after ECM processing...
  5. SoCalBruiser

    1991 Land Cruiser Code 25 and 26 after rebuild

    Testing with multimeters at idle with TE1/E1 jumpered: At 2500rpm with TE1/E1 jumpered. At 2500rpm with TE1/E1 jumper removed: 2500rpm with TE1/E1 removed, confirmed on different multimeter:
  6. SoCalBruiser

    1991 Land Cruiser Code 25 and 26 after rebuild

    Testing VF1 and VF2 with PCV hose remove, intake clamped, at 2500rpm
  7. SoCalBruiser

    1991 Land Cruiser Code 25 and 26 after rebuild

    Updating with further testing and fixes. HISTORY NOTE: The shop that did the rebuild reported CLE codes 25/26 with the original factory installed O2 sensors during test driving after the rebuild. I had them install the spare set (new) from DENSO (by way of Autozone), and they still reported...
  8. SoCalBruiser

    1991 Land Cruiser Code 25 and 26 after rebuild

    Thanks for the reply @jonheld - I took some time this weekend to continue troubleshooting. To answer your questions, and add some of my own, I'll respond to your points in order: Timing was done with TE1 and E1 jumpered on the check connector, with the idle at 650. In the FSM on page EM-11...
  9. SoCalBruiser

    SOLD FJ80 1991-1992 ECU, 89661-60080

    I might take you up on that! I have a thread going about the code 25/26 problem I'm having, and hoping for some other ideas before I blame the ECU. If anyone is curious it can be found here: 1991 Land Cruiser Code 25 and 26 after rebuild -...
  10. SoCalBruiser

    1991 Land Cruiser Code 25 and 26 after rebuild

    I have been reading every 3FE code 25 and 26 thread on this site, and after 4 weeks of troubleshooting I'm bringing this one to the community. Background: (TLDR: total engine rebuild after overheating, getting code 25/26 after ~30 mins of driving around neighborhood) In the summer of 2022 I...
  11. SoCalBruiser

    80 Series FENDER FLARE GASKET sets

    I'd like to buy a set. Finally out of the engine bay and onto the body!
  12. SoCalBruiser

    80 Series Factory Bumper Swing Out DIY Kits

    I think it’s safe to say we’re all excited about this!
  13. SoCalBruiser

    80 Series Factory Bumper Swing Out DIY Kits

    I am absolutely interested - put me down for one. Looking for a dual swing-out. Given how thirsty the 3FE is, I need to carry extra fuel. Is there an actual pre-order list going? Just curious.
Back
Top Bottom