Recent content by SJWantsADiesel

  1. S

    Lowering back to stock

    Swapped out the Dobinsons 3.5-4” lift springs for OME 2862. Took a few iterations of adjusting the lower and upper arms to get the wheelbase right and more importantly the axle parallel. Panhard bar adjustment was easier. Just had to constantly keep measuring against different reference points...
  2. S

    Lowering back to stock

    Or, do what I did - 285/75/16, 5.29 gears and an uncalibrated speedo 🤣 Thanks for the encouragement. Today, I am supposed to get the OME 861 springs for the front. Already have the rear OME 862. This weekend, I want to get the lowered springs installed, rear control arms and panhard adjusted...
  3. S

    Soflobumpers 80 series rear bumpers

    @SkyMall Did installation require cutting off the rear cross member or does it bolt to the cross member? Thanks
  4. S

    Lowering back to stock

    I drove the truck with stock 275/70/16 tires that came with stock rims I was looking for and it drives just fine. 65mph comes just shy of 3k rpm but that doesn’t bother me and engine runs smooth. So if anything, a set of new 285/75/16 will drop the rpms a bit further even. I have MetalTech...
  5. S

    Lowering back to stock

    I am not selling or parting the diff or any of the drivetrain. Only removing the armor and lowering it from riding on 35s to 33s. Arms are adjustable.
  6. S

    Lowering back to stock

    Organic cage free 80 😅
  7. S

    Lowering back to stock

    Thanks to @rtagliaferri I have a cross member now and I can get it welded 🙂 I am a little anxious about adjusting the control arms and panhard bars after I swap out the lift springs for stock height OME pair. Any advice on that part? Finally, for all you non believers, we almost hit warp...
  8. S

    Lowering back to stock

    The truck is officially off all classifieds listings. I am keeping it 😊 The back to stock might have something to do with a brand that must not be mentioned on this forum 😭 I am told hell freezes over if you own these two last of their breeds 🤣
  9. S

    Lowering back to stock

    🤣🤣🤣
  10. S

    Lowering back to stock

    I need help with the rear cross member. It was cut off to install the custom exo cage and bumper. What are my options since it needs welding - I can get it welded but where do I find a nearly cut crossmember since it can’t be unbolted at a junk yard?
  11. S

    Lowering back to stock

    Almost there with getting rid off the armor. Several interruptions, owing to kids/halloween, but the big part was getting the upper exo cage off which took a great deal of finagling. Few more bolts and this 80 will be ready for some light weight TG front and rear bumpers again like it used to...
  12. S

    Lowering back to stock

    I agree - let’s just call it a good proof of concept that a 80 can be wrapped in a roll cage 😅 Oh well, you live you learn. Yep, by end of day today, I am stripping it all off - come hell or high water 🎃
  13. S

    Lowering back to stock

    Thanks! Looks great. While searching for information on lift and springs, I ran into my post when I had just bought the LX450 and a picture of the truck from back then - most importantly my comment that despite the 35s, the truck felt pretty good to drive with stock diff gears. If you look at...
  14. S

    Lowering back to stock

    I found a set of stock alloys and 275 70r16 tires and swapped out the 35s with the steelies. Obviously, it looks cartoonish but surprisingly drove really nice. Acceleration off the stop didn’t improve much but overall responsiveness is better and freeway driving was much smoother. I suspect the...
Back
Top Bottom