Recent content by SDH

  1. S

    RTH: transfer case noise, shims, bearings

    We had a few people put it together while pressing parts so i am looking for the FSM page. 1994 fzj80-oem exhaust, 35" tires, oem engine, slinky 3". Listening to your video it might be the same or quieter. up to 50mph then the vibration starts. UGH! After the lift I had vibs at 35MPH then...
  2. S

    RTH: transfer case noise, shims, bearings

    Thanks for the update! I hear a little wine also, but getting a vibration @55. checked the outputs and feel some Axial play. Back to the drawing board maybe C clip tolerance?
  3. S

    RTH: transfer case noise, shims, bearings

    Did you find an answer to the noise etc.?
  4. S

    For Sale 4BD1T NV4500 adapter kit

    How much are you asking? I have most those parts but the center of the flywheel hole is too small for and does not fit on 4bd1t crankshaft. has it been assembled? Thanks
  5. S

    Fj60 running rough need help!

    Haha! conversation pager maybe:) Yeah i was stoked. Thanks for the insight and hope it helps someone down the (dirt) road.
  6. S

    Fj60 running rough need help!

    I'll be over this weekend!? how do i PM?
  7. S

    Fj60 running rough need help!

    Alright Bro! Initial upgrades/downgrades (ie: de-smog in Utah) -timing 9* BTDC (4450 elevation) -new wires, coil, plugs (Parts store) -Desmog following the guides on MUD -Manifold gasket (cruiser outfitters) *This fixed the huge vacuum leak -Carb rebuild kit (cruiser outfitters) Initially...
  8. S

    Fj60 running rough need help!

    Yeah! home re-build. Keystone kit from kurt with extra diaphragm. OEM Aisin carb Jets said 1.47 main 2.00 secondary. Pretty sure! I reused the original jets. They came out clean (not stripped). Thinking of putting in the 1.36/1.80 somethings from earlier 40's?
  9. S

    Fj60 running rough need help!

    Ahh! Smart... That does mean it would be further off on the CAM. Alright that is next. then check the vacuum and change the jets. Thanks for the tips :)
  10. S

    Fj60 running rough need help!

    Thanks SL, Last night i cleaned and tested the PCV valve seems ok! Also re torqued the manifold. Have not started it yet, but will this evening to test vacuum. Hoping it will be up or around 19-21. I also realized that when i did the valve adjustment i placed the flywheel to the BB not the TDC...
  11. S

    Fj60 running rough need help!

    Thanks! Looks like max would be around 22.....
  12. S

    vacuum reading

    Thank you! This gives me a good bearing....
  13. S

    Fj60 running rough need help!

    I will check the torque/bolts on the manifold. is there a trick to checking for a leak there? i tried looking for the Vac chart from output shaft, but no luck. just HAC. I have not been running to long, but the filter does not seem black or darker. If i remember right the cylinders where all...
  14. S

    Fj60 running rough need help!

    Right! i'm glad i was able to dig down and find the root problem as i have heard of burning a valve. I live in sandy, Ut. elevation around 4450. No i did not have it surfaced. just checked it with a straight edge. seemed good, but what do i know? (should have took the opportunity to surface...
  15. S

    Fj60 running rough need help!

    Hey Slow left! I couldn't find this post to reply till now! but it was a manifold gasket leak like you mentioned. also the air rail in the rear had a large crack. the air rail is gone since a desmog, but not it is running to rich to pass emissions. Although it seems to run/idle very well now...
Back
Top Bottom