Recent content by Pigcat

  1. Pigcat

    Rear Shock Plate Retainer Availability?

    Interesting, so Dobinson follows the stock setup and uses a retainer below the shock plate. I wonder if Icon missed that peculiar specification to the 80 series when they designed the stem bushing setup for our rigs. May be best to add the stock locating washer 90948-02141 under the shock plate...
  2. Pigcat

    Rear Shock Plate Retainer Availability?

    Got it! Thanks for the clarification. Each of the Icon replacement bushing sets comes with 2 of the 90948-02141 type washers along with 2 bushings and a nut. So I just need to source 1 each of the 90948-02141 retainer type washer for each side that would sandwich between the lower of the stem...
  3. Pigcat

    Rear Shock Plate Retainer Availability?

    So do you think the Icon upper stem bushings are supposed to be installed directly against the plates without using any retainer/washers? It seems like no retainer between the bushings and shock plate leaves a slight gap that results in excessive strain on the bushings. I don’t do Rubicon type...
  4. Pigcat

    Rear Shock Plate Retainer Availability?

    Thanks again. Just for my clarification, the part numbers are for the shock plates. I just need the retainer/washers that seat into those plates. Do I have to buy new plates to get the retainers/washers or can I source the retainers/washers individually? I apologize in advance for my...
  5. Pigcat

    Rear Shock Plate Retainer Availability?

    You are a god! Thank you! I’ve been to three dealerships here in San Diego and none have been able to help. Last dealer was telling me that my vin doesn’t even show I have the shock plates. Thanks again for being such a resource to our community!
  6. Pigcat

    Rear Shock Plate Retainer Availability?

    Hi all, Hoping someone out there has a solution. I have a 97’ and had an Icon Stage 3 lift installed 5 years ago. It looks like the suspension shop didn’t reuse the factory shock plate retainers. The upper stem bushings above the plates on each shock are torn up. It looks like all the...
  7. Pigcat

    Parting Out Parting 1997 Lexus LX450

    Sorry wrong button. Do you have the driver side grab handle on the A pillar. Think it is called the grip assembly part #7461060030A0.
  8. Pigcat

    Post pics of your dog(s)with your 80!

    Zack and Bannor
  9. Pigcat

    Going to be in SD this weekend. Trail recommendations

    Coming from Tucson and to escape the heat I would suggest Otay Mt Truck Trail (OMTT) starting from Pio Pico RV Resort & Campground off Otay Lakes Rd east of the city of Chula Vista. Its a shelf road with a bit of a pucker factor, simply because of the drops if anyone doesn't like heights, but...
  10. Pigcat

    ICON Reservoir/CDC adjuster incompatible with Metal Tech sliders

    Thanks again for more suggestions.
  11. Pigcat

    ICON Reservoir/CDC adjuster incompatible with Metal Tech sliders

    Yes I am concerned about the hose rubbing against the sway bar link and it also contacts the edge of the channels to what i think are the body mounts. The hose also rubs against the gusset on the slider leg supports. Also, the more I think about it I think Steve may have the solution. I didnt...
  12. Pigcat

    ICON Reservoir/CDC adjuster incompatible with Metal Tech sliders

    Thanks for the feedback. I also believe my sliders are the older MetalTech’s.
  13. Pigcat

    ICON Reservoir/CDC adjuster incompatible with Metal Tech sliders

    I would rather not have anything welded onto the frame. Im hoping that somehow spacing the ICON bracket out further from the frame will give better access.
Back
Top Bottom