Recent content by pb4ugo

  1. pb4ugo

    Dual Master Cylinder - front vs rear circuits

    Im currently using, Advics bmt090 non ABS 1" bore. In the past I used a stock drum brake 1" bore from a Oct 1971(72). B4 going to the current Advics i was using a stock 76 or later fj40 7/8" bore for disc, drum.
  2. pb4ugo

    Aftermarket tachometer

    I found these posts in the" What have you done to your land cruiser this week thread". That's in the stickies section. Ref post #43,543 https://forum.ih8mud.com/threads/what-have-you-done-to-your-land-cruiser-this-week.255593/page-2178#post-16299901
  3. pb4ugo

    Build An Accidental Frame Off..................

    We put a Fumoto valve on the sbc in our boat when the engine was rebuilt and its been great. We are able to connect a hose on it and run it out the boats drain plug hole then a flip the valve. I'd never put it on my lifted 40. I run an sbc with ramshorns and single exhaust. My exhaust is...
  4. pb4ugo

    What have you done to your Land Cruiser this week?

    You probably need to adjust the rod between the booster and master cylinder. Its putting pressure on the masters piston. You can probably find the adjustment gauge at a auto parts store.
  5. pb4ugo

    What have you done to your Land Cruiser this week?

    You'll likely have to bleed the circuit you're working on.
  6. pb4ugo

    Build 1977 FJ40 LS + H55F build

    I run a sbc/nv4500, the PO's mechanic moved the stk radiator support to the pass side in a similar way so the rad was more centered to the water pump. He used the stk radiator and shroud along with a 17" plastic flex fan. It runs cool. The extra room from moving the rad support over allowed...
  7. pb4ugo

    How do you balance a parking brake drum?

    Tire balance issues usually show up around 40mph. You might be able to have drum balanced by an engine machine shop or drive shaft shop.
  8. pb4ugo

    79 tail lights

    Can you pull the wire terminals from the 78 plug and install them into the 79 plug and add a ground to the fixture,?
  9. pb4ugo

    Help ID this 4 speed transmission from a Toyota FJ 40

    I've witnessed my stock drum E brake fail once and almost lost a good friend and my 40. Since then refuse to use it. I use my 85:1 low range gearing and strategic vehicle positioning. The link below offers some interesting options. In post #7 the OP talks about the btb kit being possibly a...
  10. pb4ugo

    Help ID this 4 speed transmission from a Toyota FJ 40

    From what I have seen and read is the disc emergency brake setup hangs down below the tcase and affects the ground clearance.
  11. pb4ugo

    Lift & Wheels Decision Making

    It appears a lot of the current aesthetics and add ons of your 40 are period correct. It's sort what was done back then. You might just consider shortening or trimming the bumper. Maybe taper the ends or something like that.
  12. pb4ugo

    1966 FJ 40 Electrical System Repair or Replace

    You can search and post a wanted ad in the Classified section. You'll likely find better deals and more help on this site than going thru ebay or someplace like that. You can also look or post in the Clubhouse section for your area. There's is a member who refurbishes gauge clusters or you...
  13. pb4ugo

    Lift & Wheels Decision Making

    Welcome to the site. Nice 40. Id get it running driving and stopping 1st. It looks to be in pretty good shape. It's great it's staying in the family. I would be choosing tires towards the end of the project. They have a date code on them and it will give you time to decide. A lot of...
  14. pb4ugo

    Build The Monkey is Back

    ^^^^^^^^^^This^^^^^^^^^^^
  15. pb4ugo

    Help ID this 4 speed transmission from a Toyota FJ 40

    I would try Cruiser Outfitters, or Valley Hybrids. Cruisermatt may have the parts too. The 4 speed is more refined, it shifts better. The 3 speeds 1st gear isnt syncronized, both the 3 and 4 speed have the same final gear of 1 to 1 ratio.
Back
Top Bottom