Recent content by Kmehr

  1. Kmehr

    Build FatherSonSJ45 Troopy

    After much research, looks like I’ve got a good plan for the rear axle to have selectable hubs. Picked up a brand new set of Aisin golds to match my front, and at the suggestion of @cruiseroutfit also got some chromoly hardened hubs gears they carry from Trailgear. Looks like I DONT need any...
  2. Kmehr

    Build FatherSonSJ45 Troopy

    Well nice surprise today digging more into the HJ61 axle- looks like it also has a limited slip carrier! Guess that’s why it was marked LSD on the outside… sadly I didn’t get lucky enough to have it already regeared to 3.7, but still! Now I can throw it in the front! Still investigating the...
  3. Kmehr

    Build FatherSonSJ45 Troopy

    Back to work on the troopy. Got my hj61 full floater pressure washed and cleaned up pretty nicely. I picked up an 80 series LSD and a new ring and pinion set. Planning to do new brake cylinders all around. I was planning to use locking hubs out back like I have on my 40 so I can flat tow super...
  4. Kmehr

    Build FatherSonSJ45 Troopy

    Yeah I was waiting to cut them till I got the caster situation sorts. Definitely rock catchers as is. I agree something appears out of the ordinary, but the improvement in feel is very real. Thankfully I doubt this will see much 4x4 over 25mph…
  5. Kmehr

    Build FatherSonSJ45 Troopy

    Yeah I think I’ll leave as is, I think the front driveshaft would really bind at 8*.
  6. Kmehr

    Build FatherSonSJ45 Troopy

    Put the 6* shims in today and and fixed 90% of the shake through the steering wheel. At full droop the transfer case side of the driveshaft is just kissing itself though, so will have to clearance if I try the 8* set. I’m happy though so going to leave as is for now.
  7. Kmehr

    Build FatherSonSJ45 Troopy

    Well you are not wrong though! I zero’d my gauge while on the spare shim, then spun it like you did and it too doubles the angle (showing 9degrees on one side, 0 on the other). The important thing though is the readings when zero’d relative to the ground show the caster angle. In any event...
  8. Kmehr

    Build FatherSonSJ45 Troopy

    Man that makes my brain hurt. I get it, but also dont haha. As to my caster, as measured by me and my certainly far from exactly precise tooling, I do think that the zero'd under the knuckle measurements reflect roughly 1* positive caster on each side +/- maybe some dirt or my fingers not...
  9. Kmehr

    Build FatherSonSJ45 Troopy

    Here is some helpful info from the instruction to my angle finder. Man, I should have read these first. The little arrow indicates the direction in which the gauge needs to be rotated to reach level:
  10. Kmehr

    Build FatherSonSJ45 Troopy

    I definitely would appreciate someone checking my work here! I did zero the gauge under each knuckle, which is definitely a variable from my spare shim bench test, which I didn't zero it between flipping it. My understanding of the angle gauge is that it is always measuring the the leading...
  11. Kmehr

    Build FatherSonSJ45 Troopy

    Well I think the twist is really only .3*. Since the little arrow on the angle finder is pointing up on one side and down on the other, they’re oriented the same way because the way I’ve taken the photos has the angle finder in a mirror image situation. Setting it to zero on my work bench...
  12. Kmehr

    Build FatherSonSJ45 Troopy

    And some photos of the new vs old shackle, steering and leafs in case I’m missing something obvious:
  13. Kmehr

    Build FatherSonSJ45 Troopy

    Ok, pulled it into my garage, used the zero feature, and a speed square that is “more straighter”:
  14. Kmehr

    Build FatherSonSJ45 Troopy

    Here’s my measurement while on my lift right after the spring install, so no shims, using the similarly inaccurate technique (I only took one side):
  15. Kmehr

    Build FatherSonSJ45 Troopy

    I’ve got 4* in there now, looking like I need some 8* shims? Seems really bizarre to need that much, don’t think I’ve ever heard of anyone installing that big on a 40 series?
Back
Top Bottom