Recent content by Jstawgn

  1. Jstawgn

    ZF 8HP Transmission Swap

    Little update Went to GXOR Trail Takeover at Merus Adventure Park this past weekend. Thanks for Dan and Shannon for coordinating this. Definitely had a blas this weekend. It's about 1200 miles one way. To me this is absolutely the best mods I did to my GX. It makes merging and passing so much...
  2. Jstawgn

    ZF 8HP Transmission Swap

    As for my project it's been running for a couple weeks. Still need to debug a few stuff. The crawl ratio is awesome. With my 4.30 gear it end up right at 52:1 Crawl ratio. Nowhere close to Jeep Rubicon but still big improvement compared to stock.The stock transmission overheat when you don't put...
  3. Jstawgn

    ZF 8HP Transmission Swap

    Chad Kulig from All Dogs Offroad been working on a project to reverse engineer the 1st Gen 8HP70 TCU from the Ram 1500. The goal is to adapt it to nissan frontier applications to work natively, but the work that's been done will eventually allow for adaptation in any canbus vehicle like GX470...
  4. Jstawgn

    100 Series LX470 8HP swap

    Canformance sells a 3D printed one that at least makes it flat and much easier to mount. I end up making some simple mount to raise it up 3-4" since the BMW shifter are so low. I also end up using G90 M5 shifter that is supported by Maxxecu. This shifter have drive mode selection button and...
  5. Jstawgn

    100 Series LX470 8HP swap

    I did not see Toyota ECU as supported. You can get cut and blip working with CANTCU? That would be the way to go of that works. Not sure what year LC ECU start using Canbus. My 05 is first year for 120 series that use canbus.
  6. Jstawgn

    100 Series LX470 8HP swap

    I think apex-control IO CAN controls all generations too. Can flash the transmission without needing addional hardware. They weren't out when I start designing my wiring. The main engineer used to be the main engineer for HTG before they went bust. Don't really know the real story.
  7. Jstawgn

    100 Series LX470 8HP swap

    I am using Maxxecu mini. You are using 2nd Gen transmission and they dont have support for that yet.
  8. Jstawgn

    100 Series LX470 8HP swap

    I end up making my own. It's not that bad although definitely recommend getting a magnifying glasses. I screw up the first CMC Molex connector because I cannot see what I am doing. The transmission is only 5 wires and shifter 4 wires. Does not even need to be connected to the TCU as it only...
  9. Jstawgn

    A750f Transmission Issues..

    A750F TCU is combined with ECU and no solenoid power would be sent out when engine not running and ECU think it needs to power one of the solenoid.
  10. Jstawgn

    GX 470 FSM .pdf for download?

    https://lexusgxor.com/_media/general:2005_gx470_techinfo.pdf This is is 3000+ pages
  11. Jstawgn

    My 2008 GX470 Sport just got hit by a drunk driver

    The damage looks minimal but most likely your rear axle are bent. It does not take much to bent rear axle from hits like that. Axle from GX460 are much cheaper than 4Runner and have KDSS bracket. You would need to buy front diff too because they are 3.91 instead of 3.73. There are companies...
  12. Jstawgn

    04 - GX470, VSC is too sensitive around corners

    Try to log it in chart mode and try to duplicate VSC activation. If you see one of the speed reading spike at the same time of VSC activation, you found the issue. When is the last time wheel bearing was replaced? They all seems to go bad around 180-220K miles. My rear wheel seal start leaking...
  13. Jstawgn

    04 - GX470, VSC is too sensitive around corners

    Toyota program the VSC very sensitive to wheel speed change. Which is also why they work very good for ATRAC. I found that bad wheel bearing or sticking brake caliper Impact this sensitivity a lot. Raised suspension and taller tire sidewall also impact the wheel speed reading. Mine used to...
  14. Jstawgn

    Toyota Land Cruiser 3-doors brake improvment ?

    Find aftermarket pads that have GG rating for friction and temperature. That would be the most cost effective. A slotted high carbon rotor might help too. Don't get drilled rotors as they are prone to cracking. Does your braking system use electric booster? Sometimes they degrade and start...
  15. Jstawgn

    Koni Raid available

    A couple years ago they are planning to release monotube 2.5" bore adjustable heights coilover. Not sure what happened with it. I did not look at KONI for my overlander due to wanting more travel. They are only available for stock travel last time I checked. I am big fan of KONI. I have owned 4...
Back
Top Bottom