Recent content by geo57a

  1. geo57a

    Series 80 engine rebuild or swap options?

    Recently overheated my FJ80 returning from a hunting trip. 250k on it. Drove it less than five minutes before I could get it cooled down. Engine began what I would describe as a "sticking lifter" sound. Drove on home about 60 miles. Parked it and later returned to drain the oil. All looked...
  2. geo57a

    1993 1FZ FE Factory Exhaust Downpipe Picture

    Runs fine. Still fighting a small exhaust leak at manifold down pipe connection.
  3. geo57a

    1993 1FZ FE Factory Exhaust Downpipe Picture

    Replacing the exhaust on my 1993. It's been a bit since I removed them, and I am hoping someone can post a picture of the factory downpipes are routed. Rounding up all the parts needed took a few weeks, and my memory isn't the best.
  4. geo57a

    93 FJ80 Steering Knuckle Issue

    Yeah, not the easiest folks I’ve ever dealt with. Parts all fit and seemed fine. I think I’ll try again with Toyota stealership seals. At this point I’m guessing I must have inadvertently damaged them during installation. I should be able to tell if I have the spring come off with the end of...
  5. geo57a

    93 FJ80 Steering Knuckle Issue

    Yes, that is the place.
  6. geo57a

    93 FJ80 Steering Knuckle Issue

    I see, I didn’t really notice the brand of bearings. I bought a front axle “kit” from Land Cruiser Parts. they seem to be a pretty knowledgeable bunch of folks. I’m still trying to get a grip on what I may have screwed up. I’m sure you know it isn’t the cleanest task around, so I really only...
  7. geo57a

    93 FJ80 Steering Knuckle Issue

    Well, my 93 currently doesn’t have shims either, but it had one thin shim ( the kit came with a couple of different thicknesses) on the top. I’m beginning to think I may have damaged the seal when I carefully slip in the axle. The drivers side is about three feet long, so I could see damaging...
  8. geo57a

    93 FJ80 Steering Knuckle Issue

    Naw, scale is true (although not recently calibrated). The knuckle turns freely with shims, and without still only has minimal resistance
  9. geo57a

    93 FJ80 Steering Knuckle Issue

    Upper and lower Trunnion bearings, and races were replaced. Not sure what exactly you are referring to as "the trunnion". FSM perhaps we have a misunderstanding of terms. Upper and lower trunnion bearings were replaced including races. The trunnion I assumed you were referring to is the round...
  10. geo57a

    93 FJ80 Steering Knuckle Issue

    I used the red High temperature grease in the wheel bearings, and then the black grease for the steering knuckle bearings. Torqued to factory specifications. Original shims were both corroded. Mic'd the original shims (.005") and used the same shim from the new kit. Any shims leave the knuckle...
  11. geo57a

    93 FJ80 Steering Knuckle Issue

    Trunnions are factory. They appear to be welded to the axle housing, so it doesn't appear they can be replaced without welding, and who knows what kind of procedure it would require. I am wondering if the trunnion bearing caps can become compressed to the point they are a few thousands shorter...
  12. geo57a

    93 FJ80 Steering Knuckle Issue

    I’m not certain my poor handling is the result of a lack of preload, but if follow the tech service manual it is impossible to get the correct preload using any shims at all. This tells me something is amiss. I have had the handling issues with the truck since I purchased it, and since I had...
  13. geo57a

    93 FJ80 Steering Knuckle Issue

    Yes, most videos just show you replacing your shims like you found them and moving on. If you go by the tech service manual you check the tension. This is where I have my issue. Getting the preload correct, using any shims at all is impossible.
  14. geo57a

    93 FJ80 Steering Knuckle Issue

    Inner axle seals are not backwards. I‘m not even sure how you would do that. The Otram video shows the tech checking the distance of the axle to the housing to verify it is properly centered. Yes, I understand most videos just showed replacing the shims that were found and going on without a...
  15. geo57a

    93 FJ80 Steering Knuckle Issue

    I am in the process of repairing my leaky front axle seals, and at the same time address the sloppy steering of my 93 FJ80. I replaced the axles, Birfields, all bearings, and seals. During the re-installation I had trouble shimming the steering knuckle to give me the 5.6-10 lbs pull the service...
Back
Top Bottom