Recent content by FranzFJ80

  1. FranzFJ80

    Parting Out  80 Wanted to Buy: Rear Bumper End Cap (Driver's Side)

    Hi, I have a 1992 FJ80. My rear bumper end cap (driver's side) is damaged, and I'd like to replace it. It's gray with chrome trim, but I'd be willing to venture beyond that and paint both to match. Anyone have one laying around?
  2. FranzFJ80

    1992 3FE Water Pump Replacement (What parts do I need?)

    Hey you know what, I did both of those last summer. I was thinking the thermostat, right?
  3. FranzFJ80

    1992 3FE Water Pump Replacement (What parts do I need?)

    Well, my water pump quickly went from a drip to a puddle. While I'm replacing it, I want to knock out as much as I can in terms of replacing parts. Besides the hoses and belts, what should I be doing? Thanks for the collective wisdom. This is a 1992 FJ80.
  4. FranzFJ80

    For Sale Tuscaloosa, AL: Massive Part Out, Motor/Trans/X-fer/Interior/Body

    Hi, do you have the upper lift gate for sale?
  5. FranzFJ80

    Blinking ABS Light

    Hi, thanks. No high pitched sound, though. Just the lights coming on. Throughout the day today, the three VSC lights have been on, but no ABS light. I'll go get it diagnosed, then go from there.
  6. FranzFJ80

    Blinking ABS Light

    Can anyone help me ID what's going on with my 2005 GX470? At the end of a 4-hour drive yesterday, I pull off the interstate and the ABS indicator started blinking, with the VSC OFF, VSC TRAC, and Anti Skid all on. I plugged in my code scanner, but the GX didn't show any fault codes (I scanned...
  7. FranzFJ80

    Air hose help on 3FE FJ80

    Thanks, that's what I'll do.
  8. FranzFJ80

    Air hose help on 3FE FJ80

    Can anyone help with a part number for the hose that goes from the middle of the intake to the valve cover (just behind the oil cap)? Mine has split at the valve cover. I know I can just get a portion of hose to fit, but if there's an actual Toyota part number, I'd rather do that. Thanks in...
  9. FranzFJ80

    3FE Air Injection Rail Removal

    P.S. The heat shield can/will stay put.
  10. FranzFJ80

    3FE Air Injection Rail Removal

    Hey hey, your pictures bring back such good memories... lol. Back it out from both sides as best you can, then pull, push and rip it out. Kudos for taking the valve cover off. I did the whole job with my valve cover on there.
  11. FranzFJ80

    3FE Air Injection Rail Removal

    So if I'm just destroying it to get it out, all I'd need to do is back the injectors out (one at a time or all at once?), then rip it out?
  12. FranzFJ80

    3FE Air Injection Rail Removal

    Here are a couple pictures of the rail.
  13. FranzFJ80

    3FE Air Injection Rail Removal

    Hi, I'm attempting to remove the air injection rail on my 1992 FJ80 w/ a 3FE. I'm having a hard time figuring out how to remove the injectors to free up the rail so I can get it out. How do you do it? I can reach the injectors fine work a wrench. I just can't figure out the process. There's the...
  14. FranzFJ80

    Axle/Birf/Flange Question for 1992 FJ80

    New birfields are the same as the old. Total length ~238 mm, outer splines, though are 35 mm. So does that mean mine are the later, longer birfs?
  15. FranzFJ80

    Axle/Birf/Flange Question for 1992 FJ80

    Thanks for the perspective and explanation. That sounds like a plan. Axle shaft + a pair of matching flanges, and I should be back in business. I'm envious of the Land Cruiser options in Australia (and elsewhere in the world). -Frank
Back
Top Bottom