Recent content by foxtrot678

  1. foxtrot678

    1HD-T Injection pump options

    A little Monday update. after putting the clear lines back on, i noticed something. i made sure all clamps were as tight as possible to eliminate any air leaks, and after sitting overnight, the clear hoses were collapsed, but with no air in them. the clear tubing had a much thinner wall than the...
  2. foxtrot678

    1HD-T Injection pump options

    i do already have the 12mm lines. i’ve replaced all rubber lines and new worm clamps for the entire feed side. i’ve also replaced the filter assembly with new oem, and even tried a racor filter system to rule out this as the culprit. clear lines from firewall to filter have no air, but line...
  3. foxtrot678

    1HD-T Injection pump options

    following up again on this. Seems I still have a leak somewhere that is letting air in, and I lose prime when it sits for more than a couple hours. I’ve torn it apart to test the filter assembly in different assemblies for leakage. The only leak I have found so far is in one of the return lines...
  4. foxtrot678

    1HD-T Injection pump options

    well… think i finally figured it out. thanks @Squash for the idea at the air again. i had moved on from that idea since i had replaced everything down line. the clear tubing showed a an obvious air leak. there were bubbles on both sides of the primer, indicating it was leaking in further back...
  5. foxtrot678

    1HD-T Injection pump options

    definitely air in the system, just put a clear hose on and there is barely fuel trickling through the hose (10% fuel and 90% air) was going to bleed the high side, but there doesn’t seem to be any air getting in the high side. what’s the best way to bleed between the primer and the pump? i...
  6. foxtrot678

    1HD-T Injection pump options

    also, this has been going on for about 3-4 months. i’ve bled the lines a few times. when it starts to die when going up hill, i am able to save it by feathering the throttle and it doesn’t die. it’s like when it returns to idle from a higher RPM, it just continues down to zero
  7. foxtrot678

    1HD-T Injection pump options

    I never updated my location apparently, i’m in Arizona
  8. foxtrot678

    1HD-T Injection pump options

    sorry, should have stated all the work done so far. - deleted ACSD - replaced all rubber lines at tank, between hard line and filter housing, and between filter housing and pump - replaced filter housing with new OEM without fuel heater - replaced fuel filter with OEM - replaced water level...
  9. foxtrot678

    1HD-T Injection pump options

    hey everyone, I have a 1993 1HD-T with a manual transmission. I’m having an issue where when I go up hills, and break at the same time, my engine will stall out when pulling up to a stoplight. It also has the same problem when making a sharp left turn, bogs out with no acceleration even with the...
  10. foxtrot678

    Arizona Classifieds / For Sale / Wanted

    have the aluminum ones off my 93 EU HDJ80. located in Surprise
  11. foxtrot678

    *FREE* stuff for local pick up - Anything and everything goes

    where are you located? been looking for a drawer for while so i can get this plastic tote out.
  12. foxtrot678

    *FREE* stuff for local pick up - Anything and everything goes

    PENDING 70 Series Fox Shocks Hey everyone! if anyone here has a 70 series, i may have some Fox shocks that fit your vehicle. they were custom made for a heavy duty off-road application. picked them up a while back thinking they might fit the 80, but not even close. cant finds the part...
  13. foxtrot678

    New Member #668 Bradley Tencer

    Hey everyone, just saw this post so a little late on the intro, my bad! i got my 80 series when i was stationed over in Germany. Was pretty much a one owner (bought from a guy who owned it for 6 months that bought it from the original owner in Belgium. been slowly fixing her up since i bought it...
  14. foxtrot678

    Bump It Offroad (BIO) - Coming (Back) Soon

    do you guys have any update on a timeline for product availability? i’ve been eyeing the step sliders for the 80, but don’t want to wait much longer to purchase some sliders.
Back
Top Bottom