Recent content by FJ45 67

  1. FJ45 67

    Early Steering Idler arm rebuild

    I have a ‘67 FJ45 , the idler arm cone bearings are very worn. Does anyone have a link to a rebuild kit for the early type ? Or an alternate solution ? I really need to keep this one on the road and safely !
  2. FJ45 67

    FJ40 H42 4 Speed 16 Spline Output Shaft Wear Evaluation

    I’m in a similiar position, what did you decide to go ? and how did it turn out ? There is an aftermarket gear available with a longer drive spline ?
  3. FJ45 67

    Gearbox Whine

    How did it turn out ? I have a whine in my transmission before and after rebuilding ? I looked up the Lucas products and cant see much for manual transmissions ? i put 90/140 in 'er and still not much difference . I used to know a fella who could get the whine out of anything ...........
  4. FJ45 67

    3-speed Transmission (J30) Questions

    Did you need to swap out the gearbox hump ? I am readying myself for this conversion soo.
  5. FJ45 67

    3 Speed T-Case to 4 Speed Transmission ?

    Yeah, my research so far is telling me that the 4spd shifter is more to the left a couple of inches , the 'lets have some fun stick' location looks ok and might work although its a different shape cutout to my original. I dont want to cut my original hump, might be time to find a replacement one...
  6. FJ45 67

    3 Speed T-Case to 4 Speed Transmission ?

    i am preparing to swap out my noisy old J30 for a noisy H41, can anyone confirm that the gear selector and hi-lo stick are in the same position ? I know the H41 is 85mm longer and a much larger box.
  7. FJ45 67

    Gearbox swap fj45

    Can I ask the benefit of going with the split transfer rather than the one piece ? are they less noisy ? Stronger ?
  8. FJ45 67

    Timing Cover Gasket pushing out, help please.

    I reckon the torque specs for the tin cover with a cork gasket are a misprint, i just did this job too, fresh reco engine but not enough care with this by my engine builder. Pulled it all off , cleaned meticulousy, new gaskets , ultra black both sides , set up one day , firm hand torque the...
  9. FJ45 67

    Transfer case differences

    I’ll keep it short. I have one piece transfer , is there a two piece transfer that will interchange ?
  10. FJ45 67

    Resealing a Fairey Overdrive

    What is the adapter advance make ?
  11. FJ45 67

    Resealing a Fairey Overdrive

    I have the sample , it’s just worn in the splines . You have the 10 spline drive sleeve ? Do you think it can be used with the later overdrive I have ?
  12. FJ45 67

    Resealing a Fairey Overdrive

    Yes, I did get those m8-m10 studs (4) It’s all a complete unit including correct shims and spacers internally. Other than the drive sleeve it’s all in very good condition . My option is to get the drive sleeve made with 10spline also a sleeve made to compensate for the smaller dia gbox main...
  13. FJ45 67

    Resealing a Fairey Overdrive

    After a lot of learning about these. I guess I’m looking for a 10spline type suitable for a 3spd box. Willing to swap my 16spline one if required to make the deal. ?
  14. FJ45 67

    Resealing a Fairey Overdrive

    I have been looking for sometime also, they are out there , it’s just motivating their caretakers to let them go. Here some pics in the mean time of mine . The shift knob is on order from UK. Gaskets are cut. 100% complete. 😊
  15. FJ45 67

    Resealing a Fairey Overdrive

    Wow , thanks Mark . Would that be the bearing sleeve (#35- 6402)? and then there is another drive sleeve (#21-6401) Interesting, When is the best time to call ?
Back
Top Bottom