Recent content by Chris T

I say no new codes as we cleared them all in one of the steps. No codes have since been generated. Tech stream reports no issues at all.

1. Unplugged, left and replugged. Did nothing. 2. Cleared all the DTCs per FSM drove around a little no new codes. 3. Per the fsm signal check the door switches all read correctly 4. Brakes are seemingly good. ACC on, pumped the pedal a bunch and the buzzer buzzed. Anything else to check? 5...

Most tests do. However this particular test from the FSM suggested by @IndroCruise uses DLC3 hence the ask.

Thank you for the repeated help, I feel like I'm loosing it. Am I being a dunce? Worked my way through steps 1 and 2 of DI-9 all fine no issues got to step 3 "bleed air out of ahc and tems system" Looking at the DLC3 port on the top row working left to right the TS pin should be the third...

The front is down on the bumps, has been since the hose failure ,the rear is not. It has remained pressurised. The front is reading -3 inches and the rear is reading 0.8 inches. I've run the pump test, that comes back inconclusive. The test results in no movement or noise from the pump...

Thanks for all the help. First up it's a 1HD-FTE Secondly, the version of tech stream I'm running is the virtual appliance from the "how to tech stream in 5 minutes" thread and it seems to work fine. Reads changes in ride height when I jack the car up , steering angle, changes of the damping...

I've read through and followed Toyota's docs for bleeding the system. I'm unable to bleed the system as the pump doesn't run so hasn't primed it. I've cracked the bleeders open and nothing. No fluid is drawn down. Hence the question about the code, could it have something to do with pump not...

so having replaced an AHC hose and shock im now dealing with an issue possibly electrical? there has previously been and error code for the rear ride height sensor. however i took that out and cleaned it. cleared the code on techstream and scanned a few times, it hasn't re appeared, so...

So having completed a replacement burst pipe I've now run into another problem the car refuses to pick itself back up. I know from running tech stream that the rear ride height sensor is throwing a DTC I plan to replace it at some point but getting the car drivable was then goal. No problem I...

Thanks for all the help chaps, got the hose all installed. Colour me an idiot what's this active test that everyone talks about, it's mentioned in the technical document as a way to deal with air in an empty system but doesn't tell you how to run it. How do I get the front end to re pressurise...

While I think of it anyone got a part number for the cushion that has the nuts attached for the hose? Just in case I end up maiming it getting it off. I've trawled amayama and can't identify it, found the other rubber cushions but can't find the metal bracket that hold the hose on.

So had a couple hours to fiddle, got the hose snaked over the frame everyone was right absolute ball ache but it's done. In the extraction phase of the old hose I snapped of one of the bolts holding down the end of the hose on to the shock. my thought was undo the 22mm nut holding the cushion...

Are there any hoses or cables that need disconnecting to lift the body that half inch? A little extra space would definitely be appreciated.

Thanks for the help chaps, had a chance to look at it today. Got the old hose of after fighting rusted bolts. The o ring and backup ring are pre installed as previously said, that's a little win. I'll pinch a bolt from else where for the mean time while I get some on order. Any tips on...

Bought it from Tuning Developments. Seems decent enough and it might have the o ring in it if it's pre pushed into the end of the hose, also it's packed with grease? Yes the 2 12mm bolts are a rusty POS so would like to replace. Just don't know what thread/ pitch and length they are. One...