Recent content by bratlas

  1. B

    2nd Gen Tundra 2UZ-FE VVT-i Rebuild Thread

    If anyone has any suggestions for aftermarket thrust bearings I'm all ears... I'm thinking the King AM-Series ones might be the ticket: TW 288AM The thrust washer is the same across the entire UZ family so I have high confidence that the 1UZ and 3UZ would have complained about them by now...
  2. B

    2nd Gen Tundra 2UZ-FE VVT-i Rebuild Thread

    I got my order in from Amayama today! I have (almost) everything I need to start assembly! One small annoyance is that my thrust bearings came damaged...Seems like it was dragged across a rough surface or fell on the ground. Not sure what to do here. I'll let the machine shop sort it...
  3. B

    2nd Gen Tundra 2UZ-FE VVT-i Rebuild Thread

    I guess I don't understand why you say that the 2UZ is sooooo much harder than a domestic truck engine. It's not like it's a BMW engine or anything. I guess I understand tolerances are tight but that's what measuring is for...and every engine needs to me checked for tolerances. I just feel...
  4. B

    2nd Gen Tundra 2UZ-FE VVT-i Rebuild Thread

    Dropped the block off today. I'm sad to leave it but I know it's in good hands and will have lots of fun playing with the other blocks :) And now we wait! I worked out a deal with the machine shop and I will be painting and assembling here. If all goes to plan, The rest of the photos in this...
  5. B

    2nd Gen Tundra 2UZ-FE VVT-i Rebuild Thread

    You have no idea what you're talking about. The 2UZ is a very straighforward rebuild candidate. If I wanted to rebuild a 5.3 or 6.0 then I would have done so. If you want to rebuild a chevy small block then go for it. I'm doing OEM selective fit main and rod bearings. Almost everything is OEM...
  6. B

    2nd Gen Tundra 2UZ-FE VVT-i Rebuild Thread

    Today I cleaned the block in preparation for sending to the machine shop tomorrow morning! And here we are after a few rounds and some elbow grease: Cleaning wasn't terrible but I should have got smaller scrub brushes. I was able to get by with a brass brush and a dremel brush bit, by hand...
  7. B

    2nd Gen Tundra 2UZ-FE VVT-i Rebuild Thread

    The short block turned out to be in much better shape. Thankfully the crank had no scoring like the camshaft. I was actually terrified to pull the crank because if they were scored, I probably wouldn't have been able to save the engine without a ton of machining. Journals have shadows of debris...
  8. B

    2nd Gen Tundra 2UZ-FE VVT-i Rebuild Thread

    When I pulled the camshafted, I was devastated to see that basically all the journals and caps were scored pretty bad. I agonized for weeks on if I should just keep and send it, but decided not to use them. It was a real bummer. Valve seats were also in really bad shape....
  9. B

    2nd Gen Tundra 2UZ-FE VVT-i Rebuild Thread

    So let's begin with the state of the engine. It was oily as heck. Both valve covers, intake manifold, oil cooler, rear main seal. Literally everything was leaking. It was leaking for so long, the steering rack was CAKED in oil/dirt.
  10. B

    2nd Gen Tundra 2UZ-FE VVT-i Rebuild Thread

    I’m starting this thread to document my 2nd gen Tundra 2UZ-FE VVT-i rebuild. This is more of a personal journey than a formal how-to. I’m not a professional engine builder, and I’m not trying to present this as the definitive way to rebuild one of these engines. I just wanted one place to...
  11. B

    Oil Cooler Leak Repair guide for 2UZFE 100 series (LC or LX)

    So you trusted some random guy on YouTube? There is no discussion about that washer upgrade anywhere online. You’re crazy man
  12. B

    Oil Cooler Leak Repair guide for 2UZFE 100 series (LC or LX)

    Why did you use 90210-22001? There are only two seals in the oil cooler assembly. The washer you replaced is not the correct. Can you show me your reference as to why you swapped a reusable steel washer with a washer 3x the thickness that is not listed to be used with a 2uz?
Back
Top Bottom