Recent content by 06Speed6

  1. 0

    Replacing alternator with magnussen SC in place.

    The pulley on the alternator should be the same, it should be a direct swap. It is probably also a good time to swap in a new belt. The belt should have a number on it if it isnt too worn, that is the part number and they are all the same across different brands. If it is too worn, you should...
  2. 0

    Sequoia Air Suspension Replacement

    It is a nice ride, and it has proven to be very capable off road.
  3. 0

    2011 Sequoia hatch problems

    I had this happen about a month ago, the latch was getting rusty. I caught it early, so I was able to fix it with some Amsoil Metal Protector. If it is completely stuck and you cannot hear it moving when you push the automatic close button, it may need to be replaced. If it seems to be moving...
  4. 0

    2011 Sequoia hatch problems

    I had this happen about a month ago, the latch was getting rusty. I caught it early, so I was able to fix it with some Amsoil Metal Protector. If it is completely stuck and you cannot hear it moving when you push the automatic close button, it may need to be replaced. If it seems to be moving...
  5. 0

    Sequoia Air Suspension Replacement

    Last weekend I basically completely replaced the rear air suspension on my Sequoia after it started leaking down overnight. I determined that the culprit was a leaky valve on the compressor, and a leaky valve on the solenoid. I think that one may have failed and took out the other, probably the...
  6. 0

    LED headlight swap issues

    I installed a set of Toyota LED headlights in my 2012 Sequoia with the xrunnerdude DRL harness since I have factory DRL. After I installed everything, the DRL appeared to work fine, they were always on, which is normal. Now, they are only on with the headlights when the switch is set to auto...
  7. 0

    Advice on running power to the rear

    The wire calculator shows a 13.8v system running 10a can use 11ga copper wire 17' with a 5% voltage drop at 140°F. I would size up one step to 10ga to get some safety margin. The 8ga suggested above would probably never give you any trouble.
  8. 0

    Flashing check engine and traction and 4LO lights "fix?"

    This happened to me on a cross-country trip in my 2012 Sequoia. I pulled the codes, and it was a transmission turbine speed sensor, which is engineer speak for a senor that measures the rpm of the torque converter. The transmission went into some kind of limp mode and wouldn't shift into...
  9. 0

    Fan pully hub assembly replacement on the 5.7L

    I had a bearing go out on the fan pulley assembly, it ruined the belt that was on it, ruined a second belt that I installed while waiting for parts, and the belts wore a groove into the pulley. Parts: Fan bracket assembly: 16380-0S010 Pulley: 16380-0S010 Fan bracket bolt x3 (optional)...
  10. 0

    What did you do with your Tundra or Sequoia this weekend?

    Swapped my headlights and grill out yesterday. Kept the headlight washers too! Now to get it painted.
  11. 0

    275/65 R20 tire on Sequoia Platinum

    That Cooper AT3 does look nice, it is very slightly larger in the 275/65 R20 size.
  12. 0

    275/65 R20 tire on Sequoia Platinum

    Thanks! I'll take a look at those
  13. 0

    275/65 R20 tire on Sequoia Platinum

    I drive off road at higher speeds. I live near Padre Island National Seashore, a 65 mile long beach where I go weekly to shark fish in the surf. The beach is 4x4 only, and I typically drive through it between 35 and 55 mph. Lots of storm debris, ruts, logs, washed up trees etc, it is completely...
  14. 0

    275/65 R20 tire on Sequoia Platinum

    I have a stock wheel, stock suspension 2012 Sequoia Platinum, anyone tried a 275/65 R20 tire on it? I know that is basically the limit, but I am also seeing online that some people are saying that the Platinum cannot run as large of a tire before rubbing. I am specifically looking at the...
  15. 0

    2nd Gen TRD grille with lights

    I picked up the Umnitza TRD grille with the DRL lights, and it looks like it comes with some wire and not much else. I have a set of LED headlights with a xrunnnerdude67 DRL harness. I can probably wire them into that harness, but is there a better way that you guys are doing?
Back
Top Bottom