cruiser lean

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jun 19, 2003
Threads
26
Messages
656
Location
Nowhere Nebraska
I know that 40's normally have a little lean to the left, but since my springs have finally broken in, the lean has gotten steadily worse. Mostly it's the left rear pack that went to crap, enough that a 1/2" shim wouldn't bring it back level.

My question is, can I pull my rear springs, open the packs and shuffle the springs? Or would it be a waste of time?

Dave
 
I for one would not do that. You might consider getting helper springs if it really bothers you. SOR sells these.
287-07-big[1].webp
 
fsusteve said:
What springs are these?

I have no idea, that Napier prick from the other thread was the guy that put the springs on for the PO. At one time there where yellow parts #'s that could be read on top of the packs, I took those numbers and looked on the net and couldn't cross them to anything.

Considering what Ige has gone through, I can help but wonder if they're Pinnacle, but that's just a guess.
 
folsom50 said:
My question is, can I pull my rear springs, open the packs and shuffle the springs? Or would it be a waste of time?

Dave

I've had some success (or luck) with that approach but sometimes it does't do anything and sometimes its gets worse. I've also gone as far as adding another leaf to a spring pack on the low side to give it more lift. But this was always with SOA. A SUA may not work as well with this approach. Not sure what you have.
 
Paul_A said:
Why not shim the opposite corner like the Toyota service bulletin recommended? I recall at least one thread on that here. It seems to work.

I would if the lean wasn't as severe as it is, right now it would take between 3/4 to 1" to level it. That's just too much of a spacer to place under the axle.
 
You might want to try a spacer or two first. A weird thing happens that results in more of a correction than the thickness of the shim. One corner goes up, one goes down, etc.
 
IDave is right. I researched the lean topic ad naseum a few months ago getting info for the new lift I am going to put on. All research said if you had the lean before the new lift - you will also have it after the new lift (and sometimes worse). I had no lean and then went to get new tires put on. They jacked up my 40 and did their work. Put it back down and I immediately noticed a lean that wasn't there before. I read others had the same experience.

Anyway - the Toytota Svc Bulletin is Volume 5 - reference:body - Nov 10 1976 - Model: FJ - Topic: Body Slant. Part number for the spacer is 48475-600100 but I do not think it is available anymore. It is basically a flat piece of steel about 5 inches long and about 3/8" thick and same width as springs. I cut mine from 3/8" stock during my welding class over the winter. You put this on the high side (PS rear for the cruiser lean) and it goes between the axle and spring pack. Just have to remove the U-bolts to install though you may need longer U-bolts after install so check. It may not make sense but it works. Toyota guys don't know why either but this is how they fix it.

BTW - the 3/8" plate (spacer) should resolve up to about 1.5" of height difference between your rear sides. By that I mean that if your DS rear is 1.5" lower, then this plate installed on the PS rear spring pack should adjust it to even (or so I've been told and read).

HTH,

AndrewT
 
I know this will sound weird, but my "lean" comes and goes. Some days it's really obvious and others it looks fine. I periodically spray the spring packs with PB Blaster and you ought to see the rust and crap work out of them. I'm getting ready to put new springs on all the way around and will wait to see what happens.
GL
Ed
 
my rig, a '71 with the tire rack on the passenger side and gas tank also on the passenger side, leans to (guess which side?) - the passenger side. The more gas in the tank- the worse the lean. Spooky- huh?
I would think that building a rack with the spare on the drivers side would help correct the lean.

-Dustin
 
After I put new springs in they started to settle more on the right side than drivers. But now the truck is almost level with a slight lean to the drivers side. Some days I see it, others it looks level. I don't think mine is that sensitive to fuel load tho. Actually the more I load it up the more level side to side it looks. If mine was really bad I personally would pull the springs out and compare static arch. I have tried the method of shuffling leafs from one pack to the other with some success. For the amount of work it is I'd just live with it or look for different springs.
 
NJFJ40 said:
IDave is right. I researched the lean topic ad naseum a few months ago getting info for the new lift I am going to put on. All research said if you had the lean before the new lift - you will also have it after the new lift (and sometimes worse). I had no lean and then went to get new tires put on. They jacked up my 40 and did their work. Put it back down and I immediately noticed a lean that wasn't there before. I read others had the same experience.

Anyway - the Toytota Svc Bulletin is Volume 5 - reference:body - Nov 10 1976 - Model: FJ - Topic: Body Slant. Part number for the spacer is 48475-600100 but I do not think it is available anymore. It is basically a flat piece of steel about 5 inches long and about 3/8" thick and same width as springs. I cut mine from 3/8" stock during my welding class over the winter. You put this on the high side (PS rear for the cruiser lean) and it goes between the axle and spring pack. Just have to remove the U-bolts to install though you may need longer U-bolts after install so check. It may not make sense but it works. Toyota guys don't know why either but this is how they fix it.

BTW - the 3/8" plate (spacer) should resolve up to about 1.5" of height difference between your rear sides. By that I mean that if your DS rear is 1.5" lower, then this plate installed on the PS rear spring pack should adjust it to even (or so I've been told and read).

HTH,

AndrewT

Yeah, that don't make sense. I'm going to try it though. I called the local NAPA to get u-bolts today, they found one in Denver and two in Billings MT, plus the fourth in who knows where, I don't remember. :bounce:

I'll also have to get new shackles in the front, but that's fine by me(it's going to be squatting in the rear). I've been wanting to get rid of those long shackles and shims in the front.
 
Makes sense if you think about it this was:

If you take two horizontal reference points, one on the axle and one on the sill, the axle reference would be at the horizon (call it 0 degrees). Say we are measuring positive degrees on a counter clockwise method so the sill would be at say 10 degrees (lean on DS). If you were to add a shim to the DS like mentioned in the service bulletin, you would not (intuitively) increase the distance between the DS tire and fender well, you would decrease it by shimming the axle toward, thus the tire, toward the wheelwell. So, the shim actually allows for a + 10 degree shift (in reference to the 180 degree mark if the left side of the sill represent 0 degrees). With that the vehicle body (in reference to the sill) would lean (for lack of better words) back toward the 0 degree (level mark). BUT, the suspension would not be and could not be true. However, the body would be level.

Just a stab. Makes sense with pencils ( :
 
NJFJ40 said:
Anyway - the Toytota Svc Bulletin is Volume 5 - reference:body - Nov 10 1976 - Model: FJ - Topic: Body Slant. Part number for the spacer is 48475-600100 but I do not think it is available anymore. It is basically a flat piece of steel about 5 inches long and about 3/8" thick and same width as springs. I cut mine from 3/8" stock during my welding class over the winter. You put this on the high side (PS rear for the cruiser lean) and it goes between the axle and spring pack. Just have to remove the U-bolts to install though you may need longer U-bolts after install so check. It may not make sense but it works. Toyota guys don't know why either but this is how they fix it.

BTW - the 3/8" plate (spacer) should resolve up to about 1.5" of height difference between your rear sides. By that I mean that if your DS rear is 1.5" lower, then this plate installed on the PS rear spring pack should adjust it to even (or so I've been told and read).

HTH,

AndrewT

I went round-and-round with a dealer on this shortly after I bought my 79 fj40 in 1979. It had the dreaded lean that I didn't notice before I bought it. I noticed it several weeks later. Anyway, back to the dealer I went and they said they could install the shim per the service bulletin. My cruiser was low about 1.5" on the rear drivers side before they installed the shim. They installed the shim on the rear passenger side. It made a difference but not close to the 1.5" it was leaning. I went back and they installed a second shim on the front passenger side. This did almost nothing to correct the rear lean. I went back a 3rd time and they measured and said "within spec" however the cruiser was obviously still leaning. If I recall, the spec was 1" or less difference side to side. So, the service bulletin or the Toyota guys may say that it can correct 1.5" of lean but what that probably means is that it can bring it to within spec, which again IIRC, is 1" or less.
 
Yeah - give it a shot and good luck. Its simple to install and the metal stock should cost you next to nothing although steel prices are going through the roof now.

Let us know how it turns out. I would think that even taking 1" out of a 1.5" lean would almost make the lean impercetible to all but the most anal observers (like us that know its there).

Regards,

AndrewT
 
I recently re arched my FJ60, and had about one inch of lean to the drivers side. Poor man's fix: I went to Home Depot and bought ten 60 lb bags of "snow sand" meant for carrying over the rear wheels of a 2wd pickup to get snow traction. I put them all on the high side, front and rear, and ran it like that for several days, trying to take it on rough roads when I could. Now the truck only leans one half inch.

For sale: 600 lbs of sand. Rust free. Great for filling up shallow graves, use in sand boxes, Jeep gas tanks, or for weighing down objects you are throwing off a bridge. Make offer. Conveniently located in Amarillo, Texas-- half way between New York and LA. :beer:
 
Back
Top Bottom