Winch Identification???

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 3, 2006
Threads
1
Messages
3
Location
Fort Worth
Greetings, I was wondering if anyone could identify make/model of my winch. Only clues are a serial number and "EP-3" stamped on it. I have contacted Superwinch who has an "EP" series, but they deny it being one of their own. Any help would be much appreciated...........
Thanks,
Ron

Winch01.webp

Winch02.webp
Winch01.webp
Winch02.webp
 
Nice clean one at that. Does it power both in and out?
should have '5697' and '6000 or 8000' stamped into the top of the gear housing. Originally it was a decal that they stamped through and sometimes the decal doesn't survive but the stamp marks do.
I guess an owner looking to make it look good again could grind or file the housing enough to obliterate the stampings, but it's worth looking close for them. The FBI has ways of raising numbers too, if you want to take it to them and risk prison:)

BTW.......:flipoff2:
 
Looks like a Bellevue (sp?). Warn bought them out. I have one and a copy of the original paperwork around somewhere.
 
does it work? it's not supposed to power out. there's a rebuild guide in the technical links section. really simple, not much to go wrong on them, manual brake is a bit of a PITA and if not used properly, you can screw up the electric motor when the cable is unspooled with the clutch disengaged because it spins the armature backwards and the windings can be expanded
 
http://www.ih8mud.com/tech/warn5687.php

other problem, you can't get any parts, but everything is so simple that a machine shop can make them cheap. I had to get the mounting holes redrilled and tapped, they were too corroded to hold a bolt. also needed to get the bolt that held the brake arm removed and a brass bushing made for the non motor end, as I couldn't get the plastic one anywhere local, and it was 25 bucks shipping from the US
learn from my mistake, if you are taking it in to the machine shop, just show them all the problems, they can do a lot of things faster than you can, and better. I think that for everything that i had done, it was like $100 or so. not that bad to bring it all back to safe and serviceable. (esp. since the winch was free.)
 
gladly said:
you can't get any parts....


Warn does not provide product support, ie. parts for this winch any longer...



However these folks purchased all of Warns old inventory for these winches some time ago and do still have some things. John Witt is the owner and very knowledgeable on these winches.




The 4 Wheel Drive Center of Minnesota
5711 W. 36th Street
St. Louis Park, MN 55416
Phone: 952-927-8811




:beer:
 
Thanks guys, My original intent was for spare parts.
I've had the 73 cruiser for 11 years but haven't paid too much attention to the winch. It has some damage from PO???. My intention is to replace the ugly bumper ( see photo ) and repair the winch at the same time.

Needed:
hand brake lining shoe ( missing)
manual clutch engagement lever ( broken)
R sided housing , non motor side ( cracked)

Might have to consider a newer, safer winch, but I will contact John in Minnesota in case he can help

Thanks for the posts,
Ron

Bumper.webp
Bumper.webp
 
I've run of those winches for 15 years and that thing is a workhorse. They must have used a diferent rating system back when they built these because I have pulled lots of people out when other 8000 lb. winches (including Warn low profile jobbies) have either not been able to or died trying.

The brake is a POS, but that thing pulls.
 
my right side housing was cracked as well, the machine shop welded it when they were doing the rest. at least you have the brake arm, mine was missing that, I found a NOS one on e-bay, but then was looking for another for a friend, and nothing to be found anywhere (didn't know about 4wd center of minn.) . if you have the parts from the clutch lever, you could likely get that welded too. I'd imagine that any parts minnesota have would be pricey given the rarity factor.
 
Back
Top Bottom