Why no CEL?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Mar 27, 2016
Threads
49
Messages
596
Location
Austin, TX
I have been working on code after code to get my 97 lx450 inspected and registered. First it was the disconnected #2 knock sensor, then it was the p0401 and I performed the resistor bypass on the egt sensor, now I'm getting p0130 and p0133. So, there's progress...

However, at no time has my CEL come on and my obd2 scanner says it's off. Why isn't it lighting up with all these codes?
 
I'll go for the low hanging fruit -

Does the "Check Engine" idiot light come on when you key over the 80?
Is it as simple as a burnt out bulb there?
 
I'm not sure what you mean by "key over".

My first thought was burnt bulb. However, my scanner actually says that the CEL is off when a code is given
 
Then the CEL lamp is burnt out or has been disconnected.

P0130 and P0133 are telling you there's a problem with the #1 oxygen sensor. The P130 code says it's a circuit malfunction, so either the sensor is missing, disconnected, or the wiring is bad.

Not sure why you think the resistor bypass on the egt sensor is going to help. Those sensors rarely go bad. Did you check the resistance of the sensor?

Are you working with a stock EGR system, or did a previous owner modify it in some way?
 
I did the egr bypass to get around p0401 so I could get inspected Saturday. However, once I did that p0130 and 133 appeared. I don't like hacks like that but I'm under time pressure.

Note: My son and I had the battery disconnected last week for another issue that's now fixed.
Now the ecu is stuck with incomplete monitors for egr, cats, o2 sensor. after performing the drive cycles for these items they're still incomplete. Obviously, this is due to sensor and/or valve issues that I cannot hack my way around.

I decided to stop screwing around and get serious. I'll be removing the resistor and fixing what's really wrong.

PO did not modify the egr system or disconnect the cel. However, he bought the truck from a "dealership" that may have tried to mask issues. Who knows...

Note: the engine does have only about 7k following a bottom and top rebuild, hot tank, new valves, etc. and new trans install the PO had that done at Peak Performance in CO Springs. He spent some major coin with them. Though, judging by the associated receipts, they did very little else "while they were in there". The throttle cable is torn up and a little rusty, some wire bundles were not tied up. I doubt the egr was touched except to take it all off and put back on. I knew about the existing p401 when I bought the truck 3 weeks ago.

While I've had to spend more time and dough getting her ready to be my dd than anticipated, I'm not completely surprised.

JB
 
Last edited:
All fixed, no codes, all monitors complete, inspection passed.

...here's what I did:

removed the throttle body and plenum

cleaned all passages with b12 carb cleaner

cleaned the MAF with MAF cleaner.

replaced all vaccume hoses that didn't feel new. One was bad enough that it alone could have caused the egr code.

Followed the fsm testing procedure for all egr and o2 sensor components.



The VSV and modulator tested bad. I replaced them with new parts. I used the non-toyota VSV and saved a bunch.

Both o2 sensors tested good.

After that, I was only getting p0133. I do have very minor exhaust leaks around flanges. However, I reasoned that these very small leaks would not likely be the cause of the code. The conflict with this was that the upstream o2 sensor did test ok. I just didn't believe it. I replaced the upstream sensor with a new denso unit.

...cleared the codes, went for a drive and all monitors completed within about 10 minutes. No code since.
 
Oh, I also manually tested the egr valve with my mouth and piece of hose. It worked great. I also cleaned it with b12 while activating the valve. This freed up the action quite a bit
 
Congratulations! Well Done. :clap:
 
Back
Top Bottom