Which suspension ?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 20, 2012
Threads
14
Messages
41
I have searched the forum and have narrowed it down to two options:
OME or Ironman. But before I pull the trigger I thought I would seek the advise of the folks on this forum.
I have a 1993 LC. I plan to mount an Ironman bumper to the front. It currently has the factory suspension and 33" tires. I would to do a 2" lift and be able to support the front bumper. Also, it would be great do this a cheaply as possible. I don't do heavy offroading and it is my wifes DD. Are there any other good solutions that I should consider other than OME or Ironman (which is slightly lower cost)? I have seen the ebay suspension from King - but dont know much about them. Any advise is appreciated.
 
If you want it cheap, but good, then don't lift, just go with the OME stock height coils. Vast improvement in ride. All that needs done is to replace the 4 coils. Caster correction is NOT needed, so saves the expense and hassle of that. You can use stock height shocks, so the factory Tokico shocks are both inexpensive and work great.

You will gain maybe an 1". No need for any lift if 33s are what you plan to keep on the truck.
 
While the experts are here.... The 4X4 Labs rear with duel swing outs is here, the ARB front, Next Venture sliders and OME 861/862 are ordered and enroute. I didn't realize the additional weight that would be added until I unloaded the rear bumper. That thing is heavy. Will all this armor weight and the weight of two to three weeks of road trip stuff still allow 33's fit under stock height OME.
 
You can start with 30mm spring spacers, but as you get heavier you will welcome the higher spring rates that the aftermarket lifts offer.
I can't recomend more the 861/862 coils or if heavy in front (bumper, batteries etc....) then 851/862. If you want more lift as you get heavier, then add spacers. Need more add a 1" body lift. If you need even more as you get heavier in your build as we all do get heavy er... Then at this point (F/R bumpers, batts, winch, rack, frig etc...) a 850J/863 would be the next move up. I would skip the medium 860 rear all together for many reasons.

33s will fit under any lift from stock to the sky. 35s will start needing bump stops.
 
Last edited:
What Greentruck said would be best for you. Those springs and shocks would be close to 600. Bucks. Good Luck..!
 
Million variations. OME and Iroman are both good to decent companies. I would give Mark @ Metaltech a buzz to discuss or any other fine vendor here.
 
While the experts are here.... The 4X4 Labs rear with duel swing outs is here, the ARB front, Next Venture sliders and OME 861/862 are ordered and enroute. I didn't realize the additional weight that would be added until I unloaded the rear bumper. That thing is heavy. Will all this armor weight and the weight of two to three weeks of road trip stuff still allow 33's fit under stock height OME.

I think you'll be OK with that on 861/862, but you'll probably want to look at rear air bags once you start loading the truck. I have lots of weight up front (see my sig line) and a drawer/camper conversion in back, which is pretty heavy. If you do have that much up front on this suspension, you'll probably need to go with the OME Nitro Sport or similar up front, as the Tokicos can't really dampen that much weight. The OP sounded plenty light enough all around that won't be an issue.

The combination of your sliders and new rear bumper may weigh more than my conversion, but probably not much once my drawers, etc were full. I want air bags mainly for when pulling the trailer to keep everything level with a full load for camping. Again, doesn't sound like an issue for the OP, but something for you to consider. The air bag install is very easy based on other's report, but will be even less work if you're putting the coils in at the same time.
 
I had a 94, with ARB Bumper and Warn 8000 winch with cable. OME with the old shocks Heavy (F) and Medium (R). The rig was totaled and IRBIS has it in CO, if you want to call Oleg and buy it used. I also had and have the same setup on 96 and 97. The 80 just drives and handles better with the change to OME over factory. Ben or Christo at SLEE are good to talk with as well. I cannot comment on Ironman.
 
I have searched the forum and have narrowed it down to two options:
OME or Ironman. But before I pull the trigger I thought I would seek the advise of the folks on this forum.
I have a 1993 LC. I plan to mount an Ironman bumper to the front. It currently has the factory suspension and 33" tires. I would to do a 2" lift and be able to support the front bumper. Also, it would be great do this a cheaply as possible. I don't do heavy offroading and it is my wifes DD. Are there any other good solutions that I should consider other than OME or Ironman (which is slightly lower cost)? I have seen the ebay suspension from King - but dont know much about them. Any advise is appreciated.
I went with OME 61/62 and Bilstein shocks. Great ride and slight lift, probably enough to do what you want.
 
Good advise all - thanks. I will target the 861/862 and take the slight lift it offers. The bumper is around 175 lb. w/o winch etc. Should be ok. Haven't decided on which shocks.
 
Good advise all - thanks. I will target the 861/862 and take the slight lift it offers. The bumper is around 175 lb. w/o winch etc. Should be ok. Haven't decided on which shocks.

try OEM, low cost, if you don't like them you can always sell them at 70% and buy something else. not really worth going over 100 a corner, if you're unsure. just my advice. - non expert, of course.
 
Last I heard, from MUD vendors, a set of 4 Tokicos was around $150 plus freight. Hard to beat that price and they work great -- unless you need some extra dampening up front like I did. I still run the Tokicos in the rear and it's a good combo with the Nitro Sports up front.
 
OEM springs or no longer as per beno about a month ago...
 
OEM springs or no longer as per beno about a month ago...

I think decoco was speaking in reference to the Tokico shocks = OEM
 
I have stock height OME 861/862 with Tokico's on 33's and am very happy with this setup.

AWL_9362.jpg
 
This is something that my interest the original poster, and interests me.

I went to my local 4wd goods provider who specializes in LC and other fun vehicles to speak about suspension.

I was trying to find out the cost/benefit of the OME stock height springs, and also what he would personally recommend.
He said that he would not recommend the stock height springs, that most people are not happy with them, as they ride too harsh since you'd need a lot of weight up front and up back to make them ride nice since they're made for a heavy load. I understood, from his explanation, they were just the heavy load spring, but shorter. He recommended going to the 2 inch lift (comfort, what I believe is called medium), for the best ride possible if you're going to re-do suspension. When I asked him about other options out there, he said... OME is a set it and forget it product, in terms that once you put it on, you'll have it for a long time and generally be very happy with the results.

What do you guys think?
 
Do you tend to drive your truck empty? In that case, the additional capacity provided by the 861/862 combo may not be ideal. However, it doesn't take much weight up front to deal with the added capacity, which is what the 861 (front, +110-250 lbs) provides. But virtually anything you add by itself, a bumper like an ARB, a winch or a 2nd battery, will be plenty and add all 3 like me and that's more than enough load. That's why I had to upgrade the front shocks to the OME Notro Sports.

The 861 (rear) is listed as simply "medium load" up to the design GVW. If you then need added capacity, choose a good set of airbags to go inside the rear coils.

In practice, the perception of harshness is mostly associated with the shocks used. If you run without added weight up front, using the OME Nitro Sports, yes, it will be harsh. But if you run the 861 /862 with the OEM Tokico shocks, you'll likely not find this to be an issue.

My guess is he's thinking of selling you a complete kit with the OME shocks and he's correct, that will be harsh. But if you just use the OME coils with the Tokico OEM shocks, you'll find that it works well and isn't harsh.
 
In practice, the perception of harshness is mostly associated with the shocks used. If you run without added weight up front, using the OME Nitro Sports, yes, it will be harsh. But if you run the 861 /862 with the OEM Tokico shocks, you'll likely not find this to be an issue.

My guess is he's thinking of selling you a complete kit with the OME shocks and he's correct, that will be harsh. But if you just use the OME coils with the Tokico OEM shocks, you'll find that it works well and isn't harsh.

I think this is correct, we didn't have a long time to talk and it was not established in the conversation that the oem shocks would be used.

Now, since we're beating the horse to death... i'd like to know if there is more than one type of OEM shock out there, you keep talking about the tokico's and I'm wondering if there's a difference between brands, or shock type coming from toyota.

AND, in the city, yes the truck is empty with no bullbar or dual battery, on trips fully loaded.
 
AFAIK, if you ask for the stock shocks for an 80 at Toyota, they'll give you the Tokicos. May want to confirm that when ordering the shocks, but I've not heard of any other supplier for those.

For those with an LX450 instead, you probably do not want the stock Lexus LX shocks (which may also be made by Tokico for all I know) as they are said to ride softer. Results with likely vary from the Toyota Tokicos, which fit the LX just fine.

I will say I only had the 861/862 on briefly before I installed the ARB, winch and 2nd battery. So not a long experience, but it seemed fine to me and at that point my truck was essentially the same as yours is now. Once I added the extra weight up front, the front Tokicos couldn't dampen all that with the new coils, which is when I swapped those to the OME Nitro Sports. Other who've gone the 861/862/Tokico route all seem satisfied with that set-up based on longer term experience than mine.

Not sure on the typical front/rear weight distribution, but adding weight between the axles will spread at least part of that to the front axle, so should help you there. Hard to say when airbags might be needed. Adding airbags is as much a matter of keeping driveshaft/u-joint angles reasonable as much as it is a weight overload thing in the 80 until you get to some real extremes of load capacity.
 
Last edited:
Back
Top Bottom