Where does the Tee go for coolant flush?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Oct 19, 2006
Threads
70
Messages
1,271
Location
Pennsyltucky
I put this in my previous overheating thread, but I'll start this one, too, hopefully to get an answer sooner. Sorry to be impatient, but I'll only be online for this afternoon and I hope to finish up my coolant/hose/t-stat project tomorrow.

So I started all my cooling system maintenance over the weekend--thanks CDan for the advice when I was ordering parts! But since I'm a :banana: moron, I'm still not sure where to place the coolant flush kit Tee after reading numerous threads about the process here. Do I install it as indicated in this pic posted by E9999?

attachment.php


Or do I put it somewhere else? Can someone post up a pic for me? I've been unable to find a good reference to all the hoses, etc. in the FSM, too. I just want to make sure I'm doing this right.

So far, the radiator has looked pretty clean when peering down the fill cap hole. The coolant drained out has been a pretty bright green color, and I've not really noticed any sludge coming out of anywhere. The T-stat looked pretty good when I replaced it as well. Still have to clean the outside of the radiator and replace a bunch more hoses, including PHH before I'm ready to flush but I'm trying to get my ducks in a row.
 
Following one of the threads on this from way back, I've always put mine into the end of the 90 degree hose that comes off the heater valve (you can see it just above the vacuum modulator in the picture you posted). I pull off the 90 degree hose from the heater valve, attach the tee to the end of it, then run a 2 foot piece of hose off the other side of the tee, and loop that hose back in to the heater valve.

Something I also did on the last flush, after flushing everything and draining it, filled the engine block with coolant through that hose, in addition to fill through the radiator. If you've read some previous threads on this, you know why.

:beer:
Rookie2
 
Thanks! That was my other choice after reading all the threads. I just wanted to make sure I was thinking the right thing.

Yes--refill the block so you have coolant in it without having to wait for the thermostat to open, right? Pour the coolant in the end opposite the heater valve?
 
FWIW, mine is still holding fine after a couple of years. I'm keeping an eye on it, though, cuz it's only plastic. Might replace it during the next coolant swap adventure. They're only a buck or so at Autozone etc.
 
Yes--refill the block so you have coolant in it without having to wait for the thermostat to open, right? Pour the coolant in the end opposite the heater valve?

Yes.

Not sure if it's important exactly what side of the heater valve you pour it in. I just poured it down the hose I had attached to the tee. I think the important thing is that your getting substantial coolant into the block.

I don't leave my tee installed. I put it on and taken it back off each time I do the flush. No particular reason, it's just not much time to install it, and it's one less place for a problem/leak to occur.

:beer:
Rookie2
 
FWIW, mine is still holding fine after a couple of years. I'm keeping an eye on it, though, cuz it's only plastic. Might replace it during the next coolant swap adventure. They're only a buck or so at Autozone etc.

The spot you chose for the T was to really focus on the heater core, right? Or will it work for the general flush as well?

Yes.

Not sure if it's important exactly what side of the heater valve you pour it in. I just poured it down the hose I had attached to the tee. I think the important thing is that your getting substantial coolant into the block.

I don't leave my tee installed. I put it on and taken it back off each time I do the flush. No particular reason, it's just not much time to install it, and it's one less place for a problem/leak to occur.

I don't think I'll leave mine installed, either. Just personal perference, I guess.
 
Back
Top Bottom