When replacing birfields

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 20, 2005
Threads
49
Messages
284
Location
Leadville, Colorado
I asked this in my $1750 thread but did not get a response...

And I searched:meh:

I was told to expect inner axles, possibly drive flanges and possibly wheel bearings at the very least.

And to budget for spiders in the diff just in case..

I have badly clicking birfs + wet knuckles... Good news was that 2+qts of diff fluid came out when I drained the front last night...

Anyone have a thought or two?
 
Are you replacing birfs or are you doing a front axle job, or both?

The spiders you talk of--which ones? The xfer case does not have a spider gear (aka: ujoint). It has a front output bearing, a center diff assy., and a rear outuput bearing.

The driveshafts have spiders (aka: ujoints)--one at each end.

I seriously doubt you will need new drive flanges (unless you have an earlier 80 series and you are getting new birfs, then yes, you will need new drive flanges to mate with the birfs that Toyota has which are the later style).

I think we need some clarification on what you are working on.

-o-
 
Are you replacing birfs or are you doing a front axle job, or both?



The spiders you talk of--which ones? The xfer case does not have a spider gear (aka: ujoint). It has a front output bearing, a center diff assy., and a rear outuput bearing.


The driveshafts have spiders (aka: ujoints)--one at each end.

I seriously doubt you will need new drive flanges (unless you have an earlier 80 series and you are getting new birfs, then yes, you will need new drive flanges to mate with the birfs that Toyota has which are the later style).

I think we need some clarification on what you are working on.

-o-

I have yet to decide if I am doing the work or someone else. Need to save up a bit.

I am going to do a full front axle job + replace both birfs with factory OEM.

I was told by the shop to also replace both innner axles at the same time.

I was told that the front wheel bearing replacement should be based on inspection.

I was also warned that the spider gears inside the third member could be worn from lack of lubrication (diff fluid leaking out the axle seals.

I am mostly trying come up with ball park of parts needed and save accordingly...
 
I have yet to decide if I am doing the work or someone else. Need to save up a bit.

I am going to do a full front axle job + replace both birfs with factory OEM.

I was told by the shop to also replace both innner axles at the same time.

I was told that the front wheel bearing replacement should be based on inspection.

I was also warned that the spider gears inside the third member could be worn from lack of lubrication (diff fluid leaking out the axle seals.

I am mostly trying come up with ball park of parts needed and save accordingly...

Ok, that makes better sense.

If you are going to replace both birfs with OEM, then yes you will need new drive flanges to go with the new birfs.

You do not have to replace the inner axles, unless you want to upgrade to cro-moly's or something else. Replacing inner axles is throwing money away.

Yes, wheel bearing replacement should be based on inspection.

I highly doubt that there is anything wrong with the spiders in the diff. They should be fine. If you had something in there, that something was probably enough.

-o-
 
But you might need to budget for new spindles. In neglected front ends, they tend to be worn enough to need replacement. Not a big deal, but it's an extra $400 in parts.

I am also a big fan of replacing wheel bearings as part of the base lining process. It just makes sense to do it if you are over 100k, and it's all apart anyway as part of the birf job.

That's too bad the birfs need to be replaced. Those guys are expensive. If you are not real hard on them, I'd be tempted to repack them and run as is. If you're going to do some hard core off roading, then replacement is safest.
 
Have you priced OEM Birfs yet? Hope you have deep pockets, they're roughly $500 a piece from Dan...
 
If I am going to do it, I am going to do it right...

I did not pay much for the cruiser... If I get 50,000 miles out of it I made out like a bandit..

If I spent 5-6k+ and then had to do birfs... I would be really upset.

EVERY 80 series that I looked at wet knuckles. Most of them had clicking going on.

Most every cruiser with less than 200k miles was 6K+

I never plan to take it "off roading"... I might take it camping, I might take it on forest service road. But it is mainly being set up for a 35 mile commute that starts at 10,000 feet and goes down to 8,000... Snowy/Ice packed roads. I have 235/85/16 Cooper M+S studded winter tires ready to go...

I four wheel for work, almost every day. In the winter I drive a sno-cat in the backcountry to mountain tops. I have absolutely no desire to do it on my personal time/dime anymore. I have done the Rubicon/Moab/Montrose/Penrose/21rd/dusy ershim trail........ in a Jeep. I sold it...
 
Slee and Cruiseparts sell birfs with a lifetime warranty for $250 each - have not heard anyone complain them yet. I like to use OEM as much as possible, in this case I did not and so far my axles are silent, my transefer case on the other is not so silent...it got dented.
 
I stopped into Slee and talked to Christo...

I bought a socket. By the time I bought the socket from sears and the 3/4" adapter I would have been more money. Slee is the cheapest I found at $25

I flat out asked about the aftermarket birfields he sells. He asked how many miles I wanted out of them. I said 100k. He said you get what you pay for, the imported aftermarket ones are 1/2 the price and not in stock right now. He recommended I go with OEM.

As for the inner axles he said it is a good possibility that a groove is worn in the seal area. Hence the recommendation for new inner axles. He did hint that the Marlin heavy duty seals might work as the seal slightly differently than stock.

Thats straight from the source. I guess I know what to do now. Take it apart, inspect, but have $1500 set aside underneath the mattress for OEM parts
 
Back
Top Bottom