Weird electrical issue

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Oct 14, 2012
Threads
5
Messages
14
Location
Central Texas
Why would pressing the brake pedal affect the brightness of the clock and ac button lights? I press the brake and they dim. When the headlights are on, they just stay dim but will brighten on occasion. Where is a good place to start troubleshooting? My guess is this is a lack of amps. Alternator? Battery? I do have an aftermarket pimp stereo and powered sub.

Any help would be great.
 
Just went through the same problem. when I pressed the brake the marker lights and interior lights would come on. it would also affect the overdrive if you turned the lights on while at speed.

I spent 2 days searching from front to back and eventually came to the trailer converter. if you have a Trailer connection just disconnect it in the rear R/H interior quarter panel. reconnect the original plugs with out the trailer harness and i'll bet problem is solved.

Now if you don't have a trailer harness you've got some work in front of you testing for a grounding short. But from what I've read after spending so much time myself i'll be you do!

Good luck.
 
I had a vaguely similar issue a few years ago. It ended up being an internal short in the battery. The battery would test fine most of the time but random vibrations would cause an internal short and only slow like 9 volts to be present. Hitting the brakes, headlights or even Turing on the stereo at Tim's would either cause the lights to dim or the truck to die for a brief second.

Good luck.
 
My thoughts:
A shorted brake circuit would cause excess load when closed, lowering the system voltage and dimming the lights. Because the headlights are affected (HEAD RH and HEAD LH circuits, they're separate,) we can rule out a problem in the TAIL circuit, which is responsible for powering the light dimmer and dash lights, and providing a dimming signal to the stereo and clock. Now the problem is isolated to the STOP circuit.

Because the problem is intermittent, that implies a loose or broken wire somewhere. Assuming there isn't a charging or battery issue, this is pretty much the same conclusion as Mountaincoolcruiser's.
 
Hello Guys, sorry to revive an old thread but I have a similar issue with a twist.
For the last week I noticed that when I hit the break / my internal clock would dim.
But, what I noticed is that when I hit the brake pedal / my dashboard lights / parking lights turn on

Literally, I hit the brake pedal and all my parking lights /side markers turn on and go off as soon as I let go of the pedal.

I did noticed too that when I turn on the headlights, my rear brakelights stay on (without stepping on the brakes)

Any ideas?
 
  • Like
Reactions: ppc
The clock dimming is a secondary effect of the tail and other lights coming on. That is normal. Concentrate on other symptoms.

One possibility is that the trailer light circuit/converter has failed allowing the brake lights to feedback into the tail light circuit. The other thing would be a failed ground. There are several posts where a connector in left rear where the jack is stored has corroded from water leaking from the moldings of the sliding windows. A similar problem with water intrusion in the driver's side kick panel with a connector caused by a leaking windshield.

Also check that the bulbs and sockets are all good in the rear lights.
 
Hello Guys, sorry to revive an old thread but I have a similar issue with a twist.
For the last week I noticed that when I hit the break / my internal clock would dim.
But, what I noticed is that when I hit the brake pedal / my dashboard lights / parking lights turn on

Literally, I hit the brake pedal and all my parking lights /side markers turn on and go off as soon as I let go of the pedal.

I did noticed too that when I turn on the headlights, my rear brakelights stay on (without stepping on the brakes)

Any ideas?


Check the Trailer wiring harness adapter in the RR fender. It may have started to melt. Do this SOON!

Secondly it could be a grounding issue with harnesses, as there are a couple points where the harness grounds to the frame, maybe one corroded or got hooked and torn off. One point is on the center of the rear crossmember I believe.
 
Back
Top Bottom