Weber 38mm 2F engine 1983

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 8, 2013
Threads
5
Messages
14
I read some good reviews on the weber 38mm ... I'm seeking better performance and willing to install weber 38mm, headers and exhaust system .... any advices recommendations suggestions :)
Thanks
 
I have a Weber 38, performance is good (now)....but we're talking about a small tractor motor. Its only going to get 'so good'. IDK about the header, I'm running a stock(ish) exhaust. I'd focus more on reliability....

Use the Search function and see what others have said. Good luck my friend!
 
What about troll hole carb and dizzy combo? That's what I have on my 78 2F and it runs strong. I concur with previous post on the tractor motor thing. Even tho it's running great I probably won't push it past 60 scooting down the highway.
 
I have a 77 FJ40 with the 2F eng., Weber Carb, Elec. Fuel Pump, D.U.I. Distributor, and Headers and I could not be happier with the set-up. It runs very strong and 65 - 70 on the highway is comfortable (w/ 4 speed & 33.5 tires).
77 FJ40 Eng.webp
 
Webber is not really any sort of upgrade over a well built stock carb.
 
The Weber is nice for a lot of setups , unfortunately the Cruisers are not one of them . The 38DGV series carb is too small , the stock carb from a 2F or a Trollhole unit is actually higher in cfm and handles angles so much better than even a modified Weber . This comes from the guy that used to build Weber carbs to run at extreme angles - the Toyota carb design is just better . On a smaller high-winding engine , now that's where a Weber will shine as that is what they were made for ...
Sarge
 
I think it depends somewhat on how you will use the truck. If it is going to be a road curiser around town a weber is not too bad. However, everyone I know that wheels their rigs uses a stock or better yet, goes with a Troll Hole Carb set up. The distributor is where you will get your best bang for your buck in my opinion.
 
Thanks to all of you guy, i live in Dubai city (United Arab Emirates) the car will mainly be used during weekends and for camping purposes in desert (off roading) in the desert i will be in need for anything that would make the vehicle performs better (higher torque and hp) .. so im looking to add power and enhance performance noting that the stock carb is working perfectly fine.
 
Unless your dizzy is hammered, you won't notice a huge performance gain by swapping it out.

Upgrades would be a new cam, shave the head for additional compression, and run a free flowing exhaust. That's about the max you can do without tearing significantly into the motor..
 
what about the distributor that MyToy72 mentioned does it have any disadvantages ... i read that it give like 20 to 30 hp and it enhances the overall performance
 
Not even close..
 
^Agreed. Only way you'd gain anything from distributor is if yours is very worn/erratic or mistimed spark, or other changes to the engine make the advance curve way off. Additional advance will help torque.
I suspect by your location your truck would be set up with minimal emission controls. Best improvements building from what you have. Assuming it is a healthy engine now, then as Mace says, shave cylinder head for higher compression ratio, exhaust, cam. Then tune the carb jets to the fuel demands. You'd have to do that with any carb swap anyways, may as well do it with the one you have. Then play with distributor advance but watch out for pre-ignition. If you have a high mileage worn out 2F now, then the above won't really help.
 
I went to the Webber last year and I am not impressed. It runs OK but if I were to do it again I would have just put a good rebuild on my stock carb.
 
I run a Procarb OEM Toyota replica (same sort of idea as a Trollhole carb) and the D.U.I. dissy and leads as shown by @tnfj and the truck starts cold with .5 to 1.5 cranks after 5 pumps of the throttle (no choke) and hot after 1-2 cranks and the throttle to the floor. (as per Toyota) I don't know if the dissy was worth the money (the carby sure was) but it was the easiest way I could find to get rid of the P.O.'s horrible aftermarket coil installation.
 
I'm running a Weber 38 and a D.U.I. Distributor and old Downey headers, and while it isn't a horsepower machine it gets me up to 65 as fast as my SM465 will go (which is not very fast because it's like driving a dump truck) . Definitely more power than stock, adding the Distributor really woke it up from the Mallory ignition I had and definitely makes startups easier. It is my second D.U.I. ignition. On both trucks the difference was immediately apparent, I know people debate the benefits but I'm a believer. The truck came with the Weber, and while it does add a little power, it's a thirsty little devil and I've never gotten it entire dialed to my satisfaction, and this is after I had to completely rebuilt by a friend at TLC. If I was to do it over I would do a Trollhole or contact Mark @ Mark's Offroad in LA, he builds a nice unit. I'm looking at fuel injection...
 
Great just great I was going to rebuild my Webber this weekend!
Now I have to get a kit for the stock carb instead. Why didn't you post this up two weeks ago?
 
Great just great I was going to rebuild my Webber this weekend!
Now I have to get a kit for the stock carb instead. Why didn't you post this up two weeks ago?

Nah. Point is, the PO has a non-emissions 2F so it is a good base to start from. But a stock long block is not going to have significant performance increase by ignition and carb alone if all parts are working well. There is nothing really unusual about what performance modifications a 2F responds to if you decide to modify for more power. Most people don't go too far with that because there are engines that have much more potential (e.g. there is a reason V8s go into so many cruisers). There are some great threads on here for building 2Fs if you search.

Webers are good carbs when set up properly. They are very adaptable to so many applications with all the jets available. The ones typically used on land cruisers have fixed cast venturis so that is not adjustable and is smaller than the stock aisin, which is able to flow more cfm at WOT. The weber 38 is synchronous opening rather than progressive. Some jets are available for the stock aisin, and what isn't could be reamed with correct sized drill bits. Weber kits seem to be ballpark set up rich to be more forgiving to a wider range of engines in varying states of tune and fuel/air needs. They don't do as well with angles/inclines or higher fuel pressure as stock carbs do.

HEI was a good trouble free ignition system in its original application (i.e. not a toyota). HEI on a land cruiser is not quite the straightforward swap many thought, and poor installations have killed engines from oil starvation and or the distributors from thrust wear (has happened with DUI as well). A good functioning vacuum advance stock distributor can work well, is way better at dealing with water, and really the only downside is parts cost/availability compared to GM HEI. HEI throws a very strong spark which can make it reliable performer or easier starting.

BTW, my 66 FJ40 runs both a weber (a too small 32dir progressive) and a freebie junk car HEI, both of which I set up years ago and have been happy with since . Initially took a bunch of trial and error testing work and time to set up right. They work well enough that as a known quantity I kept running them when I swapped in a used 2F 5yrs ago.
 
Back
Top Bottom