Water-"proofing" the electronics

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 3, 2006
Threads
259
Messages
1,935
Location
Fort Apache: Victoria
Once again, Mr T has put the essential ECU and other electronics relatively low in the vehicle.

What do you do to protect your ECU and other low-sitting electronics for water crossings? Would sealing the ECU in a zip-lok bag (with the opening glued shut) cause problems for the ECU (ie heat)?
 
are you planning on getting water in the cab up to the point of the glove box?

if you water soak the cab and do not disassemble it afterwards and dry everythign out expect to be blighted with electrical gremlins.
 
are you planning on getting water in the cab up to the point of the glove box?

if you water soak the cab and do not disassemble it afterwards and dry everythign out expect to be blighted with electrical gremlins.

Not planning on it... but one never knows, and that's the idea behind a little pre-emptive waterproofing.
 
I guess, I still don't see how you can describe that as low, did you expect them to put it in the ceiling?

there is a lot of other electronics in the cab, less in your 94 than in a 95+ but still a stack of cash, also all the interior connectors are open not waterproof like the exterior ones.

try not to drive in water over the floor level, you can go quite a bit higher if you can keep moving but if you get stuck and stop you are looking at a cab tear down.
 
Once again, Mr T has put the essential ECU and other electronics relatively low in the vehicle.

I'm actually confused by this statement. Should have Toyota put the ECU in the headliner? In all reality the ECU could have only been placed 8-10 inches higher than it currently is. After that you're into the windshield.

I'd say if you're worried about it start bagging stuff up. Just be sure to do a good job or you might acidentially trap moisture.
 
I wonder if a vacuum sealing device would help out here. My one worry would be trapping heat in the electronics and or melting bags.
 
I wonder if a vacuum sealing device would help out here. My one worry would be trapping heat in the electronics and or melting bags.

That's my concern, too. I have no problem bagging everything using a vacuum, but I'm concerned about heat dissipation.

Connectors are easy; just parrafin the whole connection.

I know there aren't a huge amount of options for the ECU placement, but where it is isn't an optimum place.

IMHO a better place for the ECU would have been high on the (in-side of the) firewall (ie behind the glovebox).

And why not the headliner? If it wasn't a huge PITA to relocate all that stuff, that's right where I'd put it.
 
Where the ECU sits doesn't bug me, but where they place the alternator defies logic, both on the 80's and on the 100's. Down low where it is susceptible to water and mud/dirt damage .....I don't get it. Even Ford Exploders have the alternator right on top of the engine where it's away from water, and easy to replace when it goes sideways. Dumb, dumb, dumb.
 
only other place to put it would be above the exhaust manifold, not sure that would have worked out very well either.
 
Where the ECU sits doesn't bug me, but where they place the alternator defies logic, both on the 80's and on the 100's. Down low where it is susceptible to water and mud/dirt damage .....I don't get it. Even Ford Exploders have the alternator right on top of the engine where it's away from water, and easy to replace when it goes sideways. Dumb, dumb, dumb.

thats cause the fords get replaced more often
 
thats cause the fords get replaced more often

Alternators and starters are the highest failure-rate components on vehicles. As such, they should be placed where access is easy. Don't get me wrong....love my Toyota....just think the locations for starter and alternator seem like an engineering afterthought..... like they forgot about it and had to slap them somewhere, despite the lack of access and ease of caked mud/water.
 
Once again, Mr T has put the essential ECU and other electronics relatively low in the vehicle.

What do you do to protect your ECU and other low-sitting electronics for water crossings? Would sealing the ECU in a zip-lok bag (with the opening glued shut) cause problems for the ECU (ie heat)?

I do water crossing every time I go out--today water just got into the trunk. One time water got over the front seats---that required removing everything including carpets/seats for the dry out production. You also need to put some type of silicone lube in all the electrical connections.

Areas of problems I have had:

Starter--I have a new one and will rebuild the old for a spare(I think I could put vents on this to keep the mud and dirt out)

Alt--dirty brushes--just have to clean it every so often

Distributor-- I was thinking about using some red high temp silicone to seal the hole--it is a real pain to take off in the field

spark plugs--(i was wondering about putting silicone around the rubber gromments?

Alarm--mine is fried

FSM--mine is 2x as big now--think about keeping it in a waterproof bag

Also you should extend your diff breathers along with the transmission and transfer case.

I have wondered if you could get something like a pelican case for the ecu--this is a reall problem for me.... the ecu scares me

I always travel with a strap connected to the tow hooks in case I need to be extracted in a hurry. Also a snorkel is a great investment.
 
something along these lines might work. Enough 80's are being wheeled now that there should be a solution.
axis_waterproof_box.webp
 
How about use an Encapsulanting/Potting compound. Pour it inside the ECU. Let is cure. The insides will be waterproof, shock resistant, and the compounds are thermally conductive.
 
Back
Top Bottom