Update

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Apr 28, 2004
Threads
70
Messages
285
Location
Orlando, Fl
well, heres an updated picture of my cruiser
question one, are the bezel police gonna nab me, question two is the rust on my bumber easty to get rid of? three, is it easier to get a new hood, or somehow fix all the rust. four, i've been thinking about a lift, and the back sags pretty bad, but which is easier, 2" or 4" and which would look better?
 
sand rider said:
well, heres an updated picture of my cruiser
question one, are the bezel police gonna nab me, question two is the rust on my bumber easty to get rid of? three, is it easier to get a new hood, or somehow fix all the rust. four, i've been thinking about a lift, and the back sags pretty bad, but which is easier, 2" or 4" and which would look better?

1) No. You got it right.
2) Is it chrome? I usually get rid of chrome and keep the rust. :flipoff2:
3) What rust?
4) They are the same as far as how easy they are to install, but there are a few factors such as how much height you want and what size of tire. I would not do it for look alone.
 
the middle weld on the hood, and the corners are rusting out, its starting to spread.... ekk. and it wouldnt be for look, the back sags almost so much to where when ever i hit a bump, the tires rub against the flares and the tub.
 
Bezel is fine (big side goes up...old ones were stamped Land cruiser)
What rust ? looks OK in the picture to me.
Stock hoods are available but not real easy to find in good condition. Removing rust on body panels (sheet metal) is just a matter of sanding it off as long as there are no rust throgh holes. Take time but is not hard to do.
2" or 4" lift by changing springs is the same. You choose the look you like and the function you want. Most off roader seem to go with 4" for the added clearance.

Good luck! Most of this stuff is 90% persperation and 10% knowledge so don't be afraid to give it a try.

Nocents
 
on the corners the rust has made holes, is it possible to weld in new corners, like flat triangles, and cut out the old parts?
 
sand rider said:
the middle weld on the hood, and the corners are rusting out, its starting to spread.... ekk. and it wouldnt be for look, the back sags almost so much to where when ever i hit a bump, the tires rub against the flares and the tub.

So do you want to step up to 35s, or are you staying with 33s? 2.5" should fit both.

Edit: yes to the above hood question.
 
Get Hellwig helper springs, picked the ass end of mine right up, went from 1" clearance to about 8" on 30" tires... Sandblast your hood, then repaint - it is economical and keeps it origional. Ok, by flipping the bezel, I couldn't do the catch thingy to open my hood, so I had to put the bezel back to normal... does this happen to you?
 
Cutting out the rust and welding in new pieces is the basic idea. flat pannels are not too bad. It gets tough if there are bends and corners as you have to form the new pieces first.

Nocents
 
im thinking about 35's because mine are pretty worn out, when its wet i get a lot of spinning on my tires, how cheap are 35's for 12(.5)x15 rims?
 
i would go with a 4in. lift if you are thinking about 35's. i went 2 1/2 and then went 35', looked OK but not enough clearance so i added a 2in. body lift. i wish i would have went 4in. lift. :doh: now i am pondering a SOA? it never ends, i thought it would be to tall now its not tall enough! good luck on what ever you decide on.
 
Back
Top Bottom