Trouble with lockers!

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 28, 2009
Threads
8
Messages
14
Greetings from a newb... I am in the middle of purchasing my bosses 96 Land Cruiser. I drive an 06 Tacoma 4x4 with no rear locker (lsd) so I have been racking my brain trying to figure out how the center, rear, & front lockers work on the 96 LC. I have read threads and the manual but am confused on some things. 1st, the manual says I have a center diff button and I do not, there is an insert that says "Toyata Security" in it's place. Will it engage automaticly when shifting into 4L? There is an indicator light that is center diff but I never see it when I start the truck(had to find with flashlight); I do see the front and rear locker indicators when I start the truck. So, I shift to 4 low and the center locker does not engage; does that make it impossible for the front and rear lockers to engage. I went through the sequence and could get the lockers to engage. I am thinking this is an electrical proplem somewhere, she (the boss) had the wiring harness replaced a couple years ago.
Any help or thoughts is appreciated!!!
 
The center diff should lock when the truck is put in 4LO. A switch for this is available - but not standard on that year.

The front and rear lockers will need the center diff locked - so you need to solve that before you can move on.
 
The first (easiest) thing to try is shifting the centre diff from high to low over and over. If low range wasn't used often (or at all) the switch in the centre diff may be gummed up and not telling the diff lock computer that the truck is indeed in low range and that it should lock the centre diff. There are a lot of threads on here about non-locking centre diff problems and how to fix them. Start with the easiest and work up from there!

And welcome! :flipoff2:
 
you may have to go from low to high up to 100 or more times before it will work. Do not short change yourself by doing it a couple of times and declaring that it does not work. As you do this you should hear some noise as it tries to work itself free. I can't remember what side you hear it on though, seems like passenger side kick panel.

Once you have the CDL light come on, then you are on to each locker respectively. Those most likely will not engage either, if it hasn't been used. Toyota used a lubricant that dries out over time if not used and that will gum up the gearing. You can try to engage the lockers and then go to some lose surface and drive in figure 8's forwards and back to try to get the rotational seperation needed to lock the diffs. When engaging the diffs, you should hear the motor of the diff lock actuator run as it drives the shaft. If that is not running check the wiring, then 12v test, then tear down if need be.

PM me if you need more help
 
This may be a stupid question (from your original post, it wasn't clear), but in addition to the center diff automatically locking when put in 4L, your truck DOES have the rotary diff. lock switch on the left side of the steering column, correct? Just want to make sure, because I have had many people tell me their truck had "lockers," only to find that their trucks just had the standard center diff lock.

Again, not trying to be a wise guy, just checking to make sure that the center diff not locking wasn't your only problem with getting everything all locked up.
 
Correct, I do have the dial on the left of the wheel for rear lockers and front and rear lockers. I spoke with my mechanic again today about the center diff indicator light not popping up and turning off at startup like the other indicator lights do, is this normal or can there be a grounding or relay issue somewhere?
Thanks!
 
The Center Diff lamp does not illuminate with the key in the start position. The lamp will come on/blink when the xfer case is put into low or the (retrofitted) CDL button is pressed. Once the center diff is locked, the lamp will stay on. Once the center diff is locked, you can lock the rear and front diffs.

You should be on a low-traction surface to test the diff locks.

If you are in the US and read in the "manual" that you have to press the CD button then you have the wrong manual for your vehicle. The CDL button was standard equipment on US spec vehicles in 1991 and 1992. All other years lock the center diff when the transfer case is in Low range.

You mention that the PO had the wiring harness replaced. We have seen at least 1 other vehicle that had the electric lock harness removed. There was no history on that particular truck so all we know is that there was no harness. There are several comprehensive posts that give specifics on how to test the center, and the F&R locks. If you are inspecting the truck, you should look underneath and be sure there are electric motors on both pumpkins. Then check to be sure there are wires going to each electric motor. Your axle code should be K294 and you will have the rotary dial. If everything looks kosher then do the testing which involves listening.

-B-
 
Last edited:
Back
Top Bottom