trans mounts SBC

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 15, 2005
Threads
59
Messages
661
Location
High Desert, SoCal
FJ40charles mentioned on another thread about using the fabbed up engine mounts seen below for transmission mounts. Does anyone have opinions or pics using them?






attachment.php
 
Last edited by a moderator:
I Like too. I am still running the stocker 3 speed and case. Would like to loose the rear Tcase mount. Are there similar trans mount options for the 3 speed?
Thanks Brad
 
I Like too. I am still running the stocker 3 speed and case. Would like to loose the rear Tcase mount. Are there similar trans mount options for the 3 speed?
Thanks Brad




There are not provisions on the earlier Land Cruiser three and four speed transmissions or transfer case assemblies for anything like the mount on that American automatic transmission pictured. Starting with the 08/80 and later four speed transmissions, (and the H55) there are provisions on the transmission housing for using an engine mount, as Toyota changed the way the engine, transmission and transfer case are mounted after that in the 40 series.




Previous to that, the transmission and transfer case assembly was allowed to hang on the flywheel housing, secured by the four bolts only, which is why, when an engine swap is done, it is required that some form of support for the engine/trans/tcase assembly is used.


I have seen (and have) older Chev flywheel housings that have provisions in them for mounting the engine similar to the earlier Land Cruiser flywheel housing, permitting you to hang the trans and tcase off the flywheel housing.
 
I was hoping someone had fabbed up something that was a little bit more substantial/conventional then the rear TC mount. My first cruiser had the earlier Chevy set up you were talking about Steve. That was back in 1972. It was a steel bell housing with a 10.5 inch clutch disc if I remember right.

Anyway thanks for the info and Isotel that is a really sweet looking setup.
Brad
 
You could always switch to a 420 and a Dana 300 (or Atlas), and a centered rear axle...(Meanwhile hemorrhaging a pile of cash) :rolleyes:



You could then use a mount similar to this:




RedAxle-40.jpg



and then gain a flat bottom skid plate....



RedAxle-27.jpg



RedAxle-48.jpg




:beer:
 
In my case my case I have an oil moisture on the back of the T-case. studs loosen up on Metel plate AA. fixed 3 times and problem still there
engine has too much power loosens up the studs need a tranny support

V8 4spdtranny & case.

options custom tranny support?
 
the AA propeller shafts always end up leaking. if you do run one, then do NOT use a gasket. try to find a large o-ring to fit in the groove on the back of the t-case and use some silicone in conjunction with that. make sure you loctite the threads.
or get rid of that x-member and either make one or have one built. this is how don aka fc187 does them. works as a trans mount, skid plate, x-member and a mount for the trac bar on soa rigs.
Copy of MVC-353S.webp
 
AA told me that I should not run a transfer case adapter on the rear and a transmission adapter at the same time. They said that it causes their adapter to break. ...

I am disappointed with what I am learning here. The AA transfer case mounting adapter leaks? So am in for a leak to come.... Hmm that sucks. I am going to try and fab a transmission mount that works on the stock cross member mounting at the end of the trans
 
fj45, the tranny on that picture is an auto & yota case? right
not able to fully appreciate
 
Did you take any pictures of this without the tcase in the way, so you can see how this is mounted to the trans?

I don't believe so. The tranny sits on the mount via the rib (which I ground flat), and the two bolts shown are the only bolts holding it to the tranny. Because of the proximity of the rubber mounts and the two bolts, I don't think there is enough torque to worry about the two bolts; I have over 30,000 miles on the setup with no adverse effects.
 
Back
Top Bottom