tow options questions

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Feb 26, 2007
Threads
28
Messages
200
Location
victoria, bc, canada
hey guys, been looking to get a way to tow my utility trailer around, without having to get a new bumper. i drive a 91 hdj81 with some metal bumper......never seen it anywhere else, mind u, its nothing special by any means.
im leaning towards a pintle/ball hitch combination by reece that bolts right onto the rear crossmember and onto the original holes, so no need for drilling, and no sacrifice of rear clearance. this is the link.
Reese Hitches.com | Trailer Hitches | Trailer Hitch Accessories | Electrical Wiring | Cargo Management | Bike Racks | Vehicle Accessories

what do u guys think of this set up, and what would u do in my shoes?, i only do light towing of my utility trailer with dirt bikes on it.

The other question i have is......what do i do for wiring?, is there a plug in kit for the 81 as there is for the 80?, if so is it available in canada?, i called my local dealership with the 80 toyota number and they said that it was an american part. im just trying to make this as easy as possible.
thanx for ur replies and suggestions.
 
Hector,

I've used this a bolt-on receiver from 4 Wheel Auto on my HDJ81 to tow a 18' sport fish boat.
Our%20hitch1.jpg


$125 at 4Wheel Auto Wholesale (PM if you want to buy mine)

If you get the style you showed you will need to find some place to hook the trailer safety chains.

I used a Hoppy 43405 kit - it was not a proper fit but a sharp knife and some tape made it work - if doing over I would splice in a "universal" kit.
see https://forum.ih8mud.com/80-series-tech/166468-hoppy-trailer-wiring-harness-doesnt-fit.html

-Steve
 
hey guys, been looking to get a way to tow my utility trailer around, without having to get a new bumper. i drive a 91 hdj81 with some metal bumper......never seen it anywhere else, mind u, its nothing special by any means.
im leaning towards a pintle/ball hitch combination by reece that bolts right onto the rear crossmember and onto the original holes, so no need for drilling, and no sacrifice of rear clearance. this is the link.
Reese Hitches.com | Trailer Hitches | Trailer Hitch Accessories | Electrical Wiring | Cargo Management | Bike Racks | Vehicle Accessories

what do u guys think of this set up, and what would u do in my shoes?, i only do light towing of my utility trailer with dirt bikes on it.

The other question i have is......what do i do for wiring?, is there a plug in kit for the 81 as there is for the 80?, if so is it available in canada?, i called my local dealership with the 80 toyota number and they said that it was an american part. im just trying to make this as easy as possible.
thanx for ur replies and suggestions.

Wife's crazy uncle has the same 4 bolt hitch you mention on his FZJ80 and he towed a 36' boat weighting twice the Land Cruiser weight for about 300 miles at 50 MPH without been noticed by the highway state troopers, (Just thinking what would happen if he had to do a panic stop since trailer's electric brake were not working) so I guess yours can handle it ;p

Regarding the wiring, the USA spec plug kit should work fine in yours but I like better to use a heavy duty kit (either the 10 or 20 amp capable type) from Draw-Tite which came in a sealed black box that has a power wire hooked directly to your battery and doesn't give any load to your stock wiring so in case you have a short circuit in your trailer lights it will not blow any of your stock fuses.

Hooking it is quite easy because all the required wires are in the left side rear quarter near the stock jack holder.

Hook your adapter ground wire to any bolt from the jack holder
Hook your adapter + 12 volt wire to the positive battery post.
Hook the following Toyota wires to your adapter labeled wires

Taillight + green
stop light green / white strip
left turn green / black strip
right turn green / yellow strip
 
Back
Top Bottom