Tire wear question

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 26, 2007
Threads
15
Messages
26
Location
Lil Rhody
Which wear quicker...the fronts, with the greater proportion of braking forces (and likely the higher weight bias), or the rears, with the greatest proportion of drive forces. The reason I ask is that my tires on the front are about to the wear indicators, and the rears have greater than 50% tread left. I could have answered my own question here, but I don't know if the PO had them rotated. I am planning on purchasing 2 new LTX's. Should the partially worn tires from the rear be placed in the front or the rear to maximize the life of all 4? Ideally, I'd be buying 4 new revos...money thing...as in a lack of.:doh:
 
Fronts wear faster. Sounds like yours were not rotated.

Now that they're different sizes, you should avoid having bigs on one side and smalls on the other, or you could end up having differential issues.

I'm not sure if having bigs up front and smalls in the rear will cause problems, but you may want to do a search and see what you find.

With full time four wheel drive, you really want to do a 5 tire rotation and keep all your tires the same size.

T.
 
On my rig with the LTX, the fronts wear just a tad faster than the rear. The problem is the outer part of the front tire wears faster than the rest of the tire. So in addition to rotating the tires, I also have the tires flipped on the rim every 20k miles.

Before you chime in on need for front end alignment, I have a lifetime alignment contract with Firestone, and they check my alignment everytime I have my tires rotated. I make sure that they give me a alignment printout to verify that the alignment has been done.

The outer part of my tire wears out on all of my other cars (all with proper alignment), so I attribute it to my habit of driving hard into the corners.
 
Holy ?rap!! I didn't even know about all this tyre rotation, I just assumed if you changed tyres they should be done in pairs, either both fronts or both rears.

My rears have a lot more tread than the fronts, infact the left hand side tyre is worn badly on the outer edge, I took the car to the local tyre dealer and he said if the tracking was out, you would have wear on both the tyres, he said if one was worn on the out side, the other will be wearing on the inside, is this correct?

I have checked over all the mechanical parts and can't find anything wrong which would make the left tyre wear badly on the outside, one thing that is concerning me now I have read a bit about the tyre diameter sizes, my fronts are a lot more worn than the backs, I have never rotated them because I didn't know you had to, :-( (don't hit me please) all I thought you had to do, was to make sure you replaced both the tyres on that same axle.

Would I have caused any damage to the drive chain? could this be the reason why my left front is wearing badly on one side? now I am worried that I have to change all four tyres :-( the cost of a tyre here in the UK is £120 = $243 inc fitting thats for Dunlop grand trek 275 x70 x 16 so I would be looking at nearly £500 !!! and grand treks are the cheapest.
 
First, it's worth mentioning that you are not driving a cheap 4WD with a chain transfer case like 99% of them. The 80 has a direct gear drive center differential.

You don't mention if you put these tires on new, or if they have an unknown history prior to you. If you bought them and the outside edge is worn funny then you have an issue. Interestingly, my bro in law's 80 was driven rearward into a stump hard enough to blow a tire and since then has worn the outside of the left rear tire. It would be good to have a shop tell you what the rear alignment is and be prepared for them to say 'we never check it because the rear cannot be adjusted.' Tell him to check it and give you a printout. On my BIL's truck we never took any action because the wear is minor if you rotate regularly, and the correction would be to replace the slightly bent rear axle housing ($$$).

DougM
 
Hi Doug... Thanks for the reply, I have had the car for about 4 years now, and have replaced all of the tyres, and always with new ones, when I got the car the fronts where quite worn, so replaced them with new Dunlop grand treks, about 2 years later replaced the two rear tyres, bearing in mind I didnt know that all the tyres should be changed and rotated to keep them even :-( I do now know.

The wear is on the front left handside tyre and on the outside of the tyre, the righthand side is wearing normally across the full width of the tread and the rears are also wearing evenly across the full width of the tread.

Do you think I should get the front wheels laser aligned, first, before I start to fit new tyres, but the tyre mechanic said it will not be the tracking, as it's only wearing on one of the front tyres and if the tracking was out, it would also be wearing on the other front tyre but on the inside.

I have had a good look under the front of the car at all the ball joints etc, I have not lifted the wheel off the ground and checked the wheel bearing yet, as the weather has been really wet here, is it a possibility that to much play in the wheel bearing could cause trye wear on the outside of the tyre?
 
My right front tire is almost bald in one spot, I believe the large lime green paint streak on the front bumper might have had something to do with it.


That was there when I got it. And since I want bigger tires anyway, I haven't bothered to get my wheels aligned.
 
wolf,

I'd wiggle and wobble things to be sure the front end parts are properly tight for your miles, and that the wheelbearings are OK. Ditto to check the 4 big bolts on the bottom of each knuckle. If you're going in for an alignment, immediately put some quality penetrating oil on the threads of the steering arms which will need to be broken loose for alignment. Wire brush the slot where you can see the threads, then apply oil so it doesn't waste time simply being absorbed into the accumulated dirt instead of penetrating the threads.

If you're SURE these tires have never been rotated even by a mechanic during routine maintenance, then I'd consider an alignment but still insist on seeing the before/after in writing and also their measurement of the rear alignment in writing (this last for your reference).

DougM
 
Tracking report

Well I had the tracking checked today, I have taken photo's of the printed reports they gave me, I wonder if they were out enough to make the left side tyre wear on the outside edge.

They show before and after reports plus an info sheet
tracking2.webp
tracking 1.webp
tracking3.webp
 
Well I had the tracking checked today, I have taken photo's of the printed reports they gave me, I wonder if they were out enough to make the left side tyre wear on the outside edge.

They show before and after reports plus an info sheet

So how is the tire wear since this alignment? I'm assuming the toe adjustment made a huge improvement.
 
Back
Top Bottom