Tire size, Break Point?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 9, 2005
Threads
71
Messages
255
Location
sykesville,md
Happy New Year everyone. Got a question about how big before breakage. I have Bobby Long 30 splines out front w/ Aussie locker so I'm not too worried about running 38" or 39" tires in the front. The rear is another story; stock axles w/ Detroit locker, can I go 38"-39" tires and not stress too much? Mostly east coast crawling, 76 FJ40, 305 sbc, soa, sm420, 35" tires , $$$$$ and more $$$$. Do you ever finish? Thanks joe b
 
I've seen those axles but was curious what others were running with stock rear axles .
 
I've got Longs 30 set in the front as well. I am running 38" tires with stock rear axles. Aussie lockers on both ends. I am hoping that the rear will hold up. I have not run it yet so I will find out soon enough.

Jeremy
 
Hi All:

I'd suggest going with the Poly Performance rear axle shafts for peace of mind. If you don't/can't spend the $450.00 on the chromo 'shafts, at least install NEW OE axle half shafts (about $200, I believe?) to replace those 25-30 year old 'shafts.

Good luck!

Alan
 
A buddy of mine has a 55 w/ 38's. Original axles and all and hasn't had any problems "yet". Had it about 2 years and we go wheelin regularly. If you don't mind, yours is SO right? What size springs are you using and what kind of tire clearance do you have? I'm looking to spring mine over and I'm curious how reasonably large I could run while still having excellent flex? sorry to hijack.
 
I've snapped a 4340 PIG chromo front inner with 37" tires....and shredded a welded-ring Longfield too....I don't run ANY stops on the front axle....my 30-spline setup is holding fine thus far (course, the housing is now bent and being replaced, but...)

I've yet to break a stock rear FJ40 or minitruck axle shaft. I did get pretty good with coarse spline rear pinions tho, even a cryo'd one didn't last a full year.
 
My boys I wheel with all run at least 40"s on their mini truck rear ends which is the same spline count as the fj40 rears and none of them are breaking shafts, they blow up thirds first. THese are pretty light trucks though. I have reason to believe that fj40 shafts may be a bit more fragile based on shaft design, I haven't broke one yet though and I beat on my pile.
 
Brian,
where did your front inner snap?
Do these have a c-clip groove machined towards the end of the axle?
 
normal_RockRash2014.jpg
 
I have seen One rear shaft bent but not broken, They are strong. But if you are going on a long trail ride i put a spare set in the rear. I use 2" ABS pipe to cover the shatfs to they dont get beat up
 
Brian,
nice pic.

Everyone else,
Dustin bent a rear shaft on his way out @Rubithon last year...good thing someone had a spare.
I believe he's running 37s in his SOA 40...
 
i have run 40 mudders since 74 on a soa and broke 1 birf last 3 years have run 38.5 15.50 radial hawgs have front and rear lockers run 35s in the winter and the 38s summer run mud hills some rocks and the stock axles work ok have 411 and 4 speed live in pa and wheel when i can i think how people drive make a difference i watch those guys on tv and they beat the crap out of their trucks till they break it and keep going and break everything id rather stop and take a new line but that could be because im almost 60 good luck
 
I am SOA w/ mostly stock springs, the original rear springs had cracks in the upper leaf so I had new upper leaves made. Any clearance problems w/ the 35" tires were due to moving the front axle foward and placing the tire center directly under the fender drop. This has been fixed by adding tube fenders and slimming the aprons. The rear has been moved back as well and I have not had any clearance issues there but the wheel wells have been cut as far as possible. Thanks for all the feedback people, I am trying to make a purchase decision: 4X4 LABS high steer( i currently run W's masterfully bent arms) or Poly Performance rear shafts. Me thinks Luke at 4X4 Labs will be getting a call cause I got spare shafts. Thanks
 
Broke one long side rear axle idling up Guardrail at Tellico, running 37" MTR's with a rear No Slip - lightly loaded with spares and tools.

Busted 3 rear pinions - once SUA, twice SOA with only a track bar - new it was dumb, just didn't have time to finish.

Front axles/birfs were another story....

Woody - was that a 30 spline Longfield - that is a sick pic, I've not seen any other pics of those broken, and all the stock ones I've seen were right at the inner spline edge.
 
I think thats a 27 spline, the 30 splines dont taper at the seal.
 
It's a 27, but interesting on where it broke...
Wouldn't the 30 and 27s have the same OD in that spot?
 
Back
Top Bottom