Tie Rod End Install Question

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 5, 2003
Threads
319
Messages
2,206
Location
San Antonio TX
OK, I am right now in the middle of replacing my TRE's and the sumbitches aren't threading in all of the way, Is there a trick or tip to this? I currently am using 2 pipe wrenches and pushing way too hard on these things. Any ideas or help would be greatly appreciated....

Thanks
Kevin
 
nspctr1 said:
OK, I am right now in the middle of replacing my TRE's and the sumbitches aren't threading in all of the way, Is there a trick or tip to this? I currently am using 2 pipe wrenches and pushing way too hard on these things. Any ideas or help would be greatly appreciated....

Thanks
Kevin

Try here, they seems to have alot to say on the subject.
 
I don't see where it has any info on re installing the TRE's . It's more on steering stabilizers.
Thanks for the help
 
Tie Rod Ends

Well, I got'em in. I used 2 24" pipe wrenches to get them on.... I got them as close as possible but it's probably gonna have to go to the alignment shop to tweak it. The TRE's that were on there didn't have a boot to be found.... They appeared to be in good shape but didn't wanna mess with taking them apart twice.. I replaced them with CCOT TRE's, I hope they hold up....
Next,,, mini disc swap....
 
Wow, all you really needed to do was loosen the collars and slide them down, pop the notched end with a thick flat head screw driver to loosen the threads and spray in some lube.

Did you follow the FSM when you did the TRE service? It gives you the starting lengths and gets them pretty close to the correct measurements.
 
i don't think they are supposed to thread in all of the way. just did mine and i only threaded them in as far as i needed to for correct wheel alignment and then locked them off with the collar, making sure that the tre's themselves are in the center of their pivot travel when the wheels are dead ahead. make sense??
 
I'm not sure what happened but on most ends there were approx 5 threads exposed on each TRE, I removed them one by one and reinstalled the new one and it would'nt go on as far as the one I just removed. They measured the same length and everything, The right wheel is a hair off and the TRE probably needs one more turn. Also, would like to get the steering wheel centered.
 
Pinion said:
Wow, all you really needed to do was loosen the collars and slide them down, pop the notched end with a thick flat head screw driver to loosen the threads and spray in some lube.

Did you follow the FSM when you did the TRE service? It gives you the starting lengths and gets them pretty close to the correct measurements.


Sorry for my ignorance but, what is FSM?
 
The unused threads get pretty grungy and rusty. Hit it with some PB Blaster or Kroil and work the tre like a tap...back and forth. I think you should adjust the centering of the steering wheel with the drag link as opposed to clocking the wheel.

GL

Ed
 
nspctr1 said:
Sorry for my ignorance but, what is FSM?


Factory Service Manual


The Bible......of sorts;)


GL

Ed
 
I sold all of the manuals I had when I had to sell my 75 a few years back. Probably wouldn't hurt to try and find another one....

While installing them I did use a pry bar to gently open the ends but once the TRE bottomed out it was tough going.

Thanks for the info...
 
Again, sorry for my ignorance but what do you mean by clocking the wheel? And , how would you adjust it with the drag link. I gotta loosen my center arm tomorrow, I took it out for a spin and the wheels didn't return and After reading a million and a half posts on the subject I finally found one that said that was the problem.... SO, while I'm in it again I can fix the mistakes...

Thanks
 
nspctr1 said:
Again, sorry for my ignorance but what do you mean by clocking the wheel? And , how would you adjust it with the drag link. I gotta loosen my center arm tomorrow, I took it out for a spin and the wheels didn't return and After reading a million and a half posts on the subject I finally found one that said that was the problem.... SO, while I'm in it again I can fix the mistakes...

Thanks

If your center arm was not a problem before, I doubt that it is now. Probably toe-in or toe-out. Drag link adjustment is covered in the FSM, and probably on this board. What I meant by "clocking" was to simply remove the steering wheel (with the tires straight) and re-install it so it looks right. If it was right before you did the tre swap then it should be right afterwards, without having to R&R it. Gitcha FSM....not Haynes, but a real FSM.
If you want to PM me with an email, I will copy and send you the pages you currently need.

Ed
 
Is there a post somewhere that gives detail step by step proceedures for changing out the TRE's? I need to do this pretty soon and dont like reinventing the wheel. I do have a FSM. I have tried a search but did not find much. Thanks in advance!!!
 
All I can tell you is spray all of them liberally with whatever penetraing oil you like the night before, look carefully at how many threads are exposed on each one, don't try to install the left-handed threads in the right-handed threads and use some anti-seize on the new ones. I still took mine to the alignment shop even though it drove just fine. They don't charge much to just set the toe.

GL

Ed
 
I am sold on Kroil. It is the best! I use anti-seize on everything. Nice to see someone else who thinks like me. I was planing on doing one at a time and compairing the old lengths to the FSM starting points. Hopefully this will work. There are a couple good posts on doing toein that i am gonna try. For centering the steering wheel, is the drag link the one attached to the pitman arm? I dont have my book in front of me. Thanks
 
IF you have push-pull steering, aka stock or mini-truck, this is the drag link...................


Ed
Draglink 001.webp
Draglink 002.webp
 
Back
Top Bottom