Temperature Sender Sheared in Block

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jun 25, 2016
Threads
1
Messages
3
Location
Portland
I have a 97 FJ80 and started to see slight overheating on my dash while on a road trip. I pulled over a few times and let it cool off and the temperature gauge would return to normal. Over the course of the trip, it would take longer and longer to "cool down", though the truck didn't seem that hot. Long story shot, the next morning when I started it up, it was reading middle center line on the temp gauge on the dash. Obviously, the sender was bad and needed to be replaced.

While backing out the temp sender, it shared off in the block at the transition down to the nipple. I tried to get an easyout on it, but it pushed further into the block and now I'm not sure how deep it is.

My question is, does anyone have any good pictures of a lower and upper block showing where the temp sender mounts into the block? I looked around on the web and couldn't find any.

temp sender.webp
 
Is it still water tight? May be hard to tell without running it, but I would not make things worse pending further advice. Off the top of my head, there are alternative ways of reading temp -- most of them better than the factory gauge. But I would not ignore the factory gauge. I just wouldn't assume that it was the sender before verifying what the temps actually are. Those readings could be symptoms of head gasket failure, radiator blockage or another common issue.

The easiest thing to do is to get one of those common OBDII readers, like a ScanGauge, available at most parts outlets. It plugs into your 97 thru a port in the dash in front of the driver's left knee. It will tell you accurately what your water temp is to the nearest degree. Even the cheapest versions of this will display your water temp in real time so you can accurately diagnose.

But someone will be along who knows better than I about what to do about the sender that's broken...for certain now...because you do want this vital system fixed.
 
If no one responds by 1030 pm eastern time I will take a pic and post when I get home. I have a bare block in the garage
Is it still water tight? May be hard to tell without running it, but I would not make things worse pending further advice. Off the top of my head, there are alternative ways of reading temp -- most of them better than the factory gauge. But I would not ignore the factory gauge. I just wouldn't assume that it was the sender before verifying what the temps actually are. Those readings could be symptoms of head gasket failure, radiator blockage or another common issue.

The easiest thing to do is to get one of those common OBDII readers, like a ScanGauge, available at most parts outlets. It plugs into your 97 thru a port in the dash in front of the driver's left knee. It will tell you accurately what your water temp is to the nearest degree. Even the cheapest versions of this will display your water temp in real time so you can accurately diagnose.

But someone will be along who knows better than I about what to do about the sender that's broken...for certain now...because you do want this vital system fixed.

The check engine light had come on and the OBDII codes pointed it to the temp sensor or thermostat, so i replaced both. It is water tight, I can thread the new temp sender into the block. I worry about starting it and running it because I have no idea where the sheared off portion of the old temp sender is and I don't want to lodge somewhere that will be harder to get out. The pictures will help to see what I'm up against. Maybe i'll get lucky and be able to power flush it out and not have to tear down the motor....
 
...The easiest thing to do is to get one of those common OBDII readers, like a ScanGauge, available at most parts outlets. It plugs into your 97 thru a port in the dash in front of the driver's left knee. It will tell you accurately what your water temp is to the nearest degree. Even the cheapest versions of this will display your water temp in real time so you can accurately diagnose...

Yes you can read coolant temperature via the OBD-II interface to the ECU. And the ECU uses a separate temperature sensor from the dash gauge, so the fact that your dash sensor is broken won't affect the ECU sensor. But this doesn't mean the OBD-II value is accurate to the nearest degree. For practicable purposes the difference may not be important to most, but we (the public at large) don't know what the accuracy specs are for the ECU sensor and its precision is no better than 1.8*F, since the ECU does it calculations using metric units and +/- 1.0*C = 1.8*F. In all likelihood, the precision is no better than 0.5 - 1.0%, which is typical for a analog sensor.

The ECU has no way to monitor the cluster's temperature gauge, so when you say the "OBDII codes pointed it to the temp sensor or thermostat" what specific codes are you talking about?
 
Yes you can read coolant temperature via the OBD-II interface to the ECU. And the ECU uses a separate temperature sensor from the dash gauge, so the fact that your dash sensor is broken won't affect the ECU sensor. But this doesn't mean the OBD-II value is accurate to the nearest degree. For practicable purposes the difference may not be important to most, but we (the public at large) don't know what the accuracy specs are for the ECU sensor and its precision is no better than 1.8*F, since the ECU does it calculations using metric units and +/- 1.0*C = 1.8*F. In all likelihood, the precision is no better than 0.5 - 1.0%, which is typical for a analog sensor.

The ECU has no way to monitor the cluster's temperature gauge, so when you say the "OBDII codes pointed it to the temp sensor or thermostat" what specific codes are you talking about?

Well, sure, that's it. But I thought shorthanding/simplifying the relative accuracies was probably the least stressful way under the circumstances to convey the point there are other ways to approach this before starting to change things. In this case, you don't want to trust the dash gauge too much, even if codes are suggesting something specific-sounding. Not legal for trade. Do not use this for commercial purposes. I approve of this message.:cyclops:;)
 
Back
Top Bottom