Tail Lights

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 4, 2009
Threads
71
Messages
476
Location
Panama City Beach, Fl
Any help would be appreciated. I have a 94 Land Cruiser, no mods. The tail lights do not turn on (which a very helpful....State Trooper informed me of).

The brake lights come on so the bulbs are good and the tail light fuse is good.

I am heading out now to try to trace the wiring, but if the brake lights work that should be good, right?

Thanks for any replies.

:flipoff2:
 
I do have a trailer harness, I'll try disconnecting it. I am in Logan, in the southeast corner.

Thanks
 
John, I'm right down the road from you, in Athens. I had a poorly installed harness from the original owner that was a mess, eventually the birdnest wiring job managed to interfere with my running lights. Once it was removed, everything worked fine.
 
Sounds good...I will disconnect soon. Started leaking out of the front diff this weekend and I took her to the shop today. I'll let ya know how it goes.
 
Disconnected trailer harness, still not working. Brake lights work but running lights don't. But...still having front axle problems so right now doesn't really matter!
 
Im not sure on the rear running lights, but the front ones run in serial. In my case battery side on my 94, there was a broken connection, which cause both the running lights in the front to be out.

Pull the rear inside plastic quarter panels. You'll see all the harness's. Use a Volt/Ohm meter to check and see where you are losing power at.
 
Had a little viscous coupler issue that made me forget all about the tail lights....

Good power at the fuse box. When I get to the rear wiring harness, the big thick one has some plugs that work (hazards) and some that don't.

I don't have a wiring diagram...yet...but looks like the wires come back to under the jack bracket, go to the right side, then back to the left.

With that said, does anyone have a diagram of the connectors or the tail light diagram? Or any good ideas?

Only hazards and turn signals work in rear.

By the way, works very nicely without the VC!

Thanks,

John
 
Last edited:
Can't figure this out.....

It has taken me a while to do some diagnostics.

Here's what I found. At main connector box behind left rear wheel, power to all light wires (that I can tell). The Green with steady is the brake light and when pedal is pressed, brake lights do work. The red with black wire, which I am sure is the tail lights, has electricity there also, I had - on the white and + on the red pole.

When I go to the connectors that actually go to the tail lights, the white is now the + and the red with black has no power. When I touch the other wires with the negative, I get current. I am assuming the running side lights jump off the tail lights.

I tried to "jump the large connector red/black wire to the tail light red wire with no success, but I was in a rush and may not have had a good connection, no light either.

Yes, the bulbs do seem to be intact but will buy a new one today to check....

Any Ideas?
 
Mine blew two at the same time last year. I started chasing my tail when a friend told me to just try bulbs, and....:beer:

Edit: I cant read
 
This might sound retarded but I'd check the bulb.

I've had something like this happen, or have the tail light coming on, but not the brake light when the pedal was pressed and slapping in a new bulb simply fixed it.

Hope that's the case!

GOOD LUCK!!
 
Have you cleaned out the sockets really well? If the wire into the socket is getting power but the contacts in the socket aren't, they probably need to be cleaned and/or replaced.

Am I reading your post right or am I offering advice that doesn't correspond?
 
My "workaround"

Thanks for all of the help, I have tried all of your suggestions.

As an update, nothing worked so I traced the wires to the harness in front, of course this is where colors change constantly but I could not find where the tail lights lose power.

So .... I took some telephone line and jumped from the fuse to the rear and spliced in (before) where the taillight harness comes off the main harness and all is working.

I am guessing that means somewhere in the harness between the fuze and the rear connector is a break in the tail light wire but that could take years and cost millions of dollars to find. This weekend I will add a more robust wire and run it through the panels to hide it.

Anyway, this will keep the Staties from pulling me over for now ;)

Again, thanks for your help all.:cheers:
 
Back
Top Bottom