Switch Dis-assembly

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Nov 5, 2006
Threads
404
Messages
1,234
Has anybody cracked the secret to taking the back of a switch like this, so that wires can be hooked directly to the terminals?


This switch happens to be the emergency flasher from a 93 4Runner, but is a pretty common configuration from what I have been able to determine.

Anybody figured out how to take the back off?
4runner flasher.webp
 
I know this is not what you're asking, but if you call C-Dan and read him the number off of the switch, he can look up if the factory connector is still available.
 
yeah its easy. Give me a minute and I will look for my write about about doing it
 
If you're trying to take the actual switch apart, you can usually carefully pry open the case with a pocket screwdriver.
If you're trying to take the harness connector apart, they make a tool for it. It's a connector pick tool. I got mine from Matco, but everybody has em. Maybe even Harbor Freight.
 
If you're trying to take the actual switch apart, you can usually carefully pry open the case with a pocket screwdriver.
If you're trying to take the harness connector apart, they make a tool for it. It's a connector pick tool. I got mine from Matco, but everybody has em. Maybe even Harbor Freight.

For the connector pin I just used a dental pick. Its cake once you know how. Some connectors come with a little door for easier access to the connector pins.
 
Thanks NLXTACY,

Your thread answers a lot of questions. I was pressing in on the side tabs, but pushing directly on the back of the switch. It looks like I need to press on the pins themselves to slide the switch forward & out.

It also looks like I need to go back to the junk yard and clip the connector out of the dash. For some reason I was hoping that if I got inside, the array of pins, to figure out what did what, would be less.

Goodness, this is just an on/off switch with a light ! Why in the heck does there have to be so many pins ? Wait . . .never mind explaining. I would never understand.

My project is to use this flasher switch to "arm" the momentary rear window switch, then use the rear window switch for an internal winch control.

If I can figure out what pins do what, will this work ?
 
Thanks NLXTACY,

Your thread answers a lot of questions. I was pressing in on the side tabs, but pushing directly on the back of the switch. It looks like I need to press on the pins themselves to slide the switch forward & out.

It also looks like I need to go back to the junk yard and clip the connector out of the dash. For some reason I was hoping that if I got inside, the array of pins, to figure out what did what, would be less.

Goodness, this is just an on/off switch with a light ! Why in the heck does there have to be so many pins ? Wait . . .never mind explaining. I would never understand.

My project is to use this flasher switch to "arm" the momentary rear window switch, then use the rear window switch for an internal winch control.

If I can figure out what pins do what, will this work ?

Yes, this will work just fine. There are enough switch contacts on the 4Runner flasher switch that you can switch both +12v to the rear window switch and ground to the winch control solenoids, just like the OEM winch control from WARN does. (WARN switches both +12v and ground as an added safety factor so that the winch can't accidentally come on if there's an electrical fault somewhere in the control system.)

The 4Runner hazard switch uses the same pin-out configuration as the FZJ80, so if you've got an EWD for your truck just look in there. (I think there's one more pin on some 4Runner switches, but you can just ignore it and follow the '80 EWD.)
 
TrickyT,

Have you diagramed this wiring approach or snaped a pic of the back of the hazzard switch with the wiring hooked up ?

If not is it something that you could draw out?

I think I have the wiring figured out for the 4runner rear window switch. but had to set the project aside. i am back at it, and figuring out the hazzard switch is the next step.
 
Back
Top Bottom