Swerving, curving, and unnerving!!

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
May 1, 2017
Threads
8
Messages
25
Location
Capo Beach, CA
Hey! Two things are happening on my 93 FJ80 that when combined get a squirrelly and unsafe and I'm hoping you can help point me in the right direction to getting it fixed.

1. My steering is a bit loose (drifty), not terrible and totally drivable just a bit more than I'd like.

2. When braking hard the steering pulls.

3. When the two come together, like breaking in a turn or slight turn, things get a little out of my comfort zone.

My questions are:
- How can I go through my steering to correct the problem? What process to I follow and where do I start? Where is the most common problems?

- What should I do about my brakes?

I bit more information about my truck: 1993 FJZ80 - 33" BFG - Old Man Emu Suspension w/heavy springs in the front and medium rear - Castor correction bushings professionally installed.

Thanks in advance for the advice and help!!
 
1) you can tighten too center nut on box to tKe up some play but ho in small increments as you can also prematrely wear with too much adj

- go through and physically grab and pull each component. Look at each end for play. Put on jackstands and watch as someone turns, see where you are losing input from piece to piece. Check each wheel/trunion bearing/tre while up in aire.

2) could be tire pull, lose wheel bearings, bent control arms or acle housing, lose knuckle, frozen caliper

Id check brake pads and see if you have a set that are fuller than others and may indicate a stuck piston not allowing full clamping force. Or stuck in and you have no more pad left...... ive seen it.
If they are all equal id inspect components mentioned above (links n bearings) for trueness and tightness. You can swap front tires left to right and see if pull changes. If so its a tire thing.
 
I just went through this on my '94. Might not be your solution, but I'll offer my observations so that you don't miss anything.

I had a DS caliper (working) with pads down to the "replace" slot; PS pads were untouched. I was sure the pistons were frozen, until I started to remove them. The pads' guide pins were rusted; no way for the pads to slide on them. I'd check this first for your "pulling" dilemma. New pads should come with new brake springs and pins. Toyota really likes the "lithium soap brake grease" by the way.
 
Steering:

- Check each rod end to make sure they are tight
- Check your wheel bearings to make sure they are not loose. One side was a bit loose on my 80 when I bought, made for a squirrelly ride.
- Steering box is likely not your issue.

Brakes:

- Check pads for even wear, front and rear
- Uneven wear up front is likely a frozen piston. Replace or rebuild caliper.
- Uneven wear out back is likely frozen caliper slider pin.

Lift:

- Your caster correction bushings may not be enough, and caster may be out of spec. Did the handling issues occur after the lift?
 
Steering:

- Check each rod end to make sure they are tight
- Check your wheel bearings to make sure they are not loose. One side was a bit loose on my 80 when I bought, made for a squirrelly ride.
- Steering box is likely not your issue.

Brakes:

- Check pads for even wear, front and rear
- Uneven wear up front is likely a frozen piston. Replace or rebuild caliper.
- Uneven wear out back is likely frozen caliper slider pin.

Lift:

- Your caster correction bushings may not be enough, and caster may be out of spec. Did the handling issues occur after the lift?


Thanks! The steering didn't really change after the lift. It was the same before and after. Is there a thread or deeper explanation on how I can check and tighten the wheel bearings. (that's not something I've done before )
 
Thanks! The steering didn't really change after the lift. It was the same before and after. Is there a thread or deeper explanation on how I can check and tighten the wheel bearings. (that's not something I've done before )


Look up wheel bearing adjustment by @Tools R Us .

Also look up "Death Wobble" for more stuff to track down.
 
Steering:

- Check each rod end to make sure they are tight
- Check your wheel bearings to make sure they are not loose. One side was a bit loose on my 80 when I bought, made for a squirrelly ride.
- Steering box is likely not your issue.

Brakes:

- Check pads for even wear, front and rear
- Uneven wear up front is likely a frozen piston. Replace or rebuild caliper.
- Uneven wear out back is likely frozen caliper slider pin.

Lift:

- Your caster correction bushings may not be enough, and caster may be out of spec. Did the handling issues occur after the lift?

My thoughts exactly.
Ducking and weaving under brakes is a sure sign of caster issues. But start with easy stuff first. I've had it occur with loose wheel bearings too.
 
Back
Top Bottom