Sticking Caliper ?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Feb 5, 2006
Threads
56
Messages
142
I have a 1996 450 and was planing on installing the new rotors and 100 series brakes I got from C-dan .
Drivers front , the pad has angled ware on the olds pads .
It looks like the top 2 pistons might be stuck ...the top of the pad has about 1/16 more meat than the bottom and is noticably worn on a angle .
Can I unstick these with out a rebuild kit or should I just bag the job and get a new caliper from C-dan .
What do these little guys cost ?
Thanks

Greg
 
Rebuild kit is cheap (like around $20). Give a go at rebuilding them (check the FAQ for procedures).

If you can't free it up or if the bore is too pitted, replace the calipers.
 
I just took a quick peek and the rubber seals are all ripper up ... I will pull them off tomarrow and see what I need and if the caliper is saveable .
Should I go with the factory rebuild kits or a parts house .

Thanks

Greg
 
i would go to oreily's and get some new calipers. as a matter of fact that is what i did. you'll save a bunch of time, which is money (unless its a saturday)
 
I put Oreilly calibers on my FJ 62 about 6 years ago and I haven't had any proplems. They had them in stock also and they weren't very expensive. I don't know what CruiserDan charges.
 
I dont have an Oriley near me ...I use to be in the automotive business so I still have an accout with a big parts house ... I pay list on parts .
I have spent all the money on the factory rotors , Toyota has not let me down yet .
I guess I will have to do the numbers , I Have the lx at my shop and tomarrow I am going to pull all 4 corners and see what else I find .
I know the fluid looks like it's original ... dark and golden ...so the whole system needs flushing .
I have all the seals to do the brinfields and I have the time so I may just do every thing .
Can you beleave this all started with me pulling the header pipe to weld a crack in the Y of the header pipe .
I dont mind doing the rebuilding of the calipers , if there going to last a year ...it's not worth all the wasted time ... just go new .
Thanks guys .

Greg
 
CruiserDan has the rebuild kits if you go that way. He also has new ($$$) calipers for the 96 and rebuilt (very reasonable) calipers for the <95.

After working on my seized pistons for a while, I gave up and ordered the rebuilt calipers from CDan. They fit perfectly, and are working well on my 97.
 
What is the differance between the 96 and 95 calipers ? Are they a direct replacement ?
I have the 100 series pads that are going to be installed and new factory rotors . This puts the project way over budget ... but since I have allready invested this much I will proibly do all four corners , I will know more when I pull the calpiers apart and inspect for rust .
Thanks

Greg
 
As far as I can tell, they're a direct replacement. There's something different, but, AFAIK, Toyota doesn't publish/disclose what it is. The pistons are the same, the other parts that interface with the caliper (lines, knuckle, etc.) are identical.

Because it is not the official part for the later rigs, CDan won't recommend it.

I decided to give'm a go, and am very pleased.

I ordered new pins & retaining clips at the same time (cheap). I'm running 100 series pads.
 
I'm down my shop now ... In spected all four corners ...I don't feel rebuilding is an option ...One of the front calipers looks different than the other ...one looks like is has a galvinized finsh and the other is all rusty , so I am assuming one is not original .
The back look pretty corroaded .
My parts house is closed and so is toyota ...I can wait ...I will do some research ...
The Pre 96 sounds like the ticket , I don't feel like blowing 300 bucks a side .
Any one know the cost and if the rear are availible in rebuilt .
Thanks

Greg
 
Give CruiserDan a call. You can find his number in the Vendor section or the American Toyota banner ad that pops up periodically at the top of the page.

You should consider adding a signature and filling out your profile. It really helps others know where you are and what you have. :)
 
I apologize to every one about the signature ...I will do it this week !
I'm out of eastern Pa.
The job gets worst ...LOL
Looks like I have to do inter axle seal ...I allready have them ...before joing this site and finding one of the greatest parts guys I have ever known .... C-Dan is the man !
I bought a front end service kit from cruiser outfitters , I have a complete kit including Koyo bearings all the seals and gaskets and bearings .
So it looks like I'm doing a front end service ... I pulled the rotors off and found plenty of luberocation on the bearings ...too much they smelled of gear oil and I could tell the gear oil had gotton in there ... not bad but enought to know the seals were failing .
I have yet to pull the spindels to check the brifs and the spindel bushing condition ... I will do that tomarrow.
Thanks guys
Greg
 
Ah, you're well on your way then.

DougM
 
Back
Top Bottom