Starter Woes...

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Nov 10, 2005
Threads
360
Messages
4,040
Location
КАГІҒОЯИІА
Posted here before about my starter.

When the vehicle gets warmed up and then you shut it down, it sometimes does not want to start again without tapping on the starter with a hammer while someone turns the key.

You get the solenoid click when you turn the key but the starter just does not want to kick in.

Checked all connections up one side and down the other and all looks great.

Bought a brand new Toyota re-man starter from CDan and had the guy who did my gears throw it in a couple of weeks ago.

Well, it had the same problem almost immediately.

I hate banging on my brand new starter with a hammer but that was the only way to get it started at the gas station a little while ago.

Now that I have two perfectly good starters with hammer dings in them. :frown:


Any ideas? I am starting to get grumpy.
 
Posted here before about my starter.

When the vehicle gets warmed up and then you shut it down, it sometimes does not want to start again without tapping on the starter with a hammer while someone turns the key.

You get the solenoid click when you turn the key but the starter just does not want to kick in.

Checked all connections up one side and down the other and all looks great.

Bought a brand new Toyota re-man starter from CDan and had the guy who did my gears throw it in a couple of weeks ago.

Well, it had the same problem almost immediately.

I hate banging on my brand new starter with a hammer but that was the only way to get it started at the gas station a little while ago.

Now that I have two perfectly good starters with hammer dings in them. :frown:


Any ideas? I am starting to get grumpy.
Plunger bad, same deal, about 20$ in parts from crazy parts guy and no problem, still have dings where I kept hitting it.....
 
x2 plunger.

I had the same problem a while back when I replaced the contacts and plunger. The plunger ended up being a bit too long.
 
I guess the plunger is the next step.


Sure would be mine also, it's the cheapest fix. I just was thinking it's hard to admit that a new starter would have a bad plunger or contacts. I have heard of one or two other people getting new remaned starters and having issues with the solenoid.
 
Pull your starter and test it yourself or take it to Pep Boys and they can test it. You'll see if the motor and the plunger works consistently or not.
 
When I was chasing my no start problem I was able to verify it wasn't in the starter by using a volt meter on the wire going to the solenoid (which must be left plugged into the solenoid while testing to keep it under load). When I had no start I was not getting volts to the solenoid to kick it over and at that point I knew the problem was elsewhere. In the meantime I made a wire to plug into the solenoid when it wouldn't start, instead of pounding the starter I just unplugged factory wire to solenoid and plugged in mine and touched the other end to the battery and it fired each and every time. If it's your starter then going straight to the battery shouldn't work either. Just another test for the starter I guess.

I don't think it's in your starter.
 
Sounds like the solenoid. Bought a new one for a chevy starter a few weeks ago and solved the problem which was the same as you describe.

I'm guessing that you folks mean solenoid when you say "plunger"?
 
A remanufactured starter should have new plunger and contacts. Of course, after beating it with a hammer.........?
I would warranty out the starter and see if that solves it.
 
Confirm that you battery connections are tight!!

Mine were not which, so after I changed out the contacts and plunger in the dirt at the deer lease it still wouldn't start. Ruined a weekend of deer hunting but I learned a valuable lesson.
 
Back
Top Bottom