something bugging the hell out me me(front hose on valve cover)

[cruiser88]

This things runs like a champ..........damn near burn the tires(LOL) BUT ANYWAY NO real antifreeze other than a real small thermstat housing, 5 k never had to fill it.

drained oil, no water

pvc sucks like its suppose to BUT the front hose on the valve cover blows,all the time. After it warms up it looks like steam)does not taste of antifrezze) no extra fluids in my crankcase no where.

I have a weber, the pvc is hooked down low ...........I am sure that has nothing to do with it


The only only moisture under my cap appears to be normal for a really wet/damp winter. Nothing that I have never seen before.

I thought this hose was suppose to to suck not blow, its the one on the front that goes to the webber filter /housing.

I am sure this is simple,however I do know I have slight valve seal leak at warmup but there is no way this is related.

 

[liljlandon]

You mean the one that is just curled over behind the fill cap? Mine was originally supposed to hook back into my weber, but it would fall off if the going got bumpy.

I just let it droop and drip onto the top of my leaf spring, when it drips. Every morning I have about two drops of moisture. The only difference I see between letting it hook up to the weber is that i dont burn the excess oil off through my engine, but seeing as ive never had oil come out at any rate, it hasnt bugged me.

 

[cruiser88]

I did they same for a while but now I want it hooked up.

There is no way in hell it could be blow by right being it has that plate/gasket under the valve cover?

I did have oil breifly, I might still have I dont know? I dont see anything showing me there is now

 

[cruiser88]

where is your pvc hooked to your carb?

I might have mine hooked up wrong

 

[cruiser88]

ok now I am fairly certain it has to do with my pvc location..............if you have any pictures of your hook up................hook a brother up

 

[liljlandon]

Any of these help? If they dont, hook me up with an email addy and ill send ya one when i leave tomorrow.

 

[liljlandon]

EDIT: Disregard, i shouldnt do homework and mud at the same time.

 

[cruiser88]

I cannot tell where the other end of the pvc is going

 

[liljlandon]

So I remember!

Now, the red arrow pointing to the red circle is the hole that you could plug or use the supplied fitting (green arrow) to hook up your pvc to and thats where i put mine. (im 95% positive.)

 

[cruiser88]

gottcha..........I will check it out

So I remember!

Now, the red arrow pointing to the red circle is the hole that you could plug or use the supplied fitting (green arrow) to hook up your pvc to and thats where i put mine. (im 95% positive.)

 

[liljlandon]

Ill double check in the morning for ya.

 

[cruiser88]

I might be changing a valve seal this weekeed to............

Ill double check in the morning for ya.

 

[liljlandon]

Here ya go, sorry i didnt post this morning... I took the picture and realized I had no way to put it on a computer at the time...

 

[cruiser88]

My weber is diffrent......I will check back when I get the chance,brother thanks for your help

 

[liljlandon]

Sorry im not much help then...

 

[WristPin]

On mine it had a hole in the lower half of the airfilter housing. in that hole was a plastic 90 deg elbow bolted on that i hooked the pcv hose to.

it looked like weber made it that way.

 

[cruiser88]

but should it be blowing?

On mine it had a hole in the lower half of the airfilter housing. in that hole was a plastic 90 deg elbow bolted on that i hooked the pcv hose to.

it looked like weber made it that way.

 

[WristPin]

but should it be blowing?

yes! imagine like its recycling or as a circuit. make sure the valve cover baffle is intact, not cut

 

[cruiser88]

baffle?

yes! imagine like its recycling or as a circuit. make sure the valve cover baffle is intact, not cut