Simple question: Running board removal

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Apr 26, 2009
Threads
51
Messages
189
Location
Salt Lake City, UT
Hey,
So I finally pulled the running boards off, but the rear mounts are kind of a pain to get off. A ratchet does not fit because of the body mounts and a box end will not fit either. What did everyone else do?

I would like to avoid torches and grinders since I would like to reuse those holes to mount up sliders. What magical tool/technique am I missing. I think myself pretty handy with the wrench but this one has me stumped.

BTW, the truck looks 100% better already. Sliders, front flaps, tall skinny tires, and we'll be looking pretty nice.
 
You're saying you want to reuse the holes that the b/s running boards were mounted to for sliders?????

cheers,
george.
 
You're saying you want to reuse the holes that the b/s running boards were mounted to for sliders?????

I'm taking the granny boards off the truck but I want to use the mounting holes left on the truck to mount up sliders. That is why I am trying to avoid more drastic measures such as torches, cut discs, or grinders.

I am a :banana::banana::banana: mechanic that has found himself stumped on this simple thing.
 
I just used a ratchet with a flex head. It was sorta of pain, at one point I got the ratchet stuck and had to repeat step 6 about 4 times. It eventually agreed to come out.
 
Using those same bolt holes to mount up sliders is a mistake IMO. You would be attaching them directly to the body, you take a good hit to the slider and you have just caused a few grand in rocker damage. That is why all aftermarket sliders are mounted to the frame. The 80 is one heavy pig. If you are going to mount sliders do it right the first time, you will be glad you did. Do a search and you will find tons of info on how to mount sliders properly.:D Good luck.
 
1/4" ratchet an 12mm socket will get it most of the way out. Then switch to an end wrench if necessary.
x2 on the frame mounts unless you are talking about adding some bracing to the body in addition to the frame mounts (still not too sure about that)
 
Thought this would be a fitting thread to ask this question as well.

With the floor boards removed, do people re-install the bolts back into the locations? I put mine back with a very simple logic of plug it back up.
 
I took the 2 nuts off the bottom of the body bolts , dropped the bushings, and got in there with an air ratchet and swivel socket, removed the running board bolts, then put back together. It was kind of an out of the way step, but easier than tryin to fit tools into a small space. And as stated above, sliders probably should be mounted to the frame and not existing running board mounting holes, they wouldn't be sturdy enough to take a hit.
 
Good call. I was always assuming that all the professional sliders mount up to the same holes. I will make the necessary changes to my design of the sliders. Mounting to the frame will make protecting the cat that much easier as well.

I would buy sliders but I cannot bring myself to drop so much cash when I could just spend a Sunday with a welder and torch and come up with similar results.
 
No swivels for me, as was said in an earlier post:

http://www.gearwrench.com/catalog/wrenches/ratcheting/flex_combination/

I f-ing love these things...if you dudes don't own a set...you need to get these or something like them! They make life a lot easier.

However, the D/S rear bolt, its related tac-welded nut in the body broke free after say ten turns :-(. Thank god for my next favorite tool...the Sawzall! It was loose enough to cut without damaging the body.
 
Can't wait to see what you come up with...keep us posted!
 
Back
Top Bottom