shift lock problem

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Feb 23, 2006
Threads
97
Messages
952
Location
NE Texas
I am trying to get my 94 6.2 diesel conversion going again and think my shift lock is causing some starting problems. First of all the shift lock is not working, I am not using the A442 transmission so all of the wiring to the transmission is gone, does the shift lock go through the trans wiring? I assumed it was unrelated. I am also not getting any power to my starter wire (not the big one from the battery) wondering if the shift lock has anything to do with this?
Rusty
 
You might have to jump the connection to the neutral safety switch. The wire comes from the transmission (the original one) and passes along the "hump" on the passenger side (U.S.) close to the top of the transmission. I think it is a gray connector (2 prongs) and it is circular instead of square or rectangular. It has been a while since I jumped mine due to a bad Neutral Safety Switch but I know it is connected to the starting circuit because my truck wouldn't start unless it was in neutral. I had to stick a short piece of wire to jump the connector on the ENGINE side of the plug................you probably don't have the TRANSMISSION side of the connector in the truck anymore since you are using a different trans. My cruiser is a '91, but I think they all have a nertral safety switch. Jumping this wire makes the cruise control useless. There is probably a way around this, but I didn't go any further than simply jumping the wire.
Good Luck and I hope this helps!
 
Is the neutral safety switch on the transmission? I have the Black/white wire coming (I think from the ignition) out the firewall. It goes from there to the 2 plug round connector with a Black/red wire. From the connector it changes to a black wire and a white wire going to the transmission (not any more in my case) My thinking is that the current flows like this, from the ignition through the black/white wire to the plug where it changes to either the black or white wire going to the transmission (neutral safety switch?) the power returns (if it is in park) through either the white or black wire to the black/red wire which goes to the starter motor. I thought that by eliminating the plug and just using the black/white wire I could run it straight to the starter, bypassing the switch on the transmission but I am not getting any power from the black/white wire in the start position (at least not on my test lamp)
If you can follow me am I thinking right?
Rusty
 
The Neutral Safety Switch is bolted to the driver's side of the original transmission. It is shaped somewhat like a triangle and has a shaft going through it. It is about the size of a cd. I kind of follow your thinking about how the current flows. What I know from experience is that my truck would start in neutral, but not park with the NSS hooked up. I bypassed the switch instead of continuing to start in neutral. Typically you start in park and go one click down the shift column which puts you in reverse. Start in neutral and one click down the column puts you in drive. After almost driving through the back wall of my garage (through force of habit) a couple of times I bypassed the switch. My wires are as follows: From ignition side of the connector - black/red and black/white. From the trans. side of the connector - solid black and solid white.
I crimped 2 spade connectors to each end of a short piece of wire. I plugged one end into the black/red and the other into the black/white on the ignition side of the connector. This allowed current to get to the starter circuit but also disabled the cruise control. It might be worth a try to stick a piece of wire in the connector creating continuity between the black/red and black/white wires.
good luck
 
I have basically already done that, once I thought I had the wiring figured out I clipped the wires leaving me just the black/white wire coming out of the firewall. I was going to splice into that and take it to the starter motor. I decided to test it with a test light and when I turned the ignition to the start position the test light did not light up, maybe I don't have a good ground on my test light. It is possible the engine isn't grounded? My first thought though is that it probably went throught the shift lock. I remember a few times with my old 94 I would turn the key and nothing happened, I could wiggle the shifter a bit and it would start. In my current situation the shift lock isn't working, at least it won't let me shift out of park with the ignition on. Am I correct in my thinking? If so what should I check?
Rusty
 
I guess I'm confused on your black/white wire. My black and white come up from the transmission, but I have a 3FE so there is more space between the firewall and the back of the engine for me to trace where it originates. The wires I jumped are black with a red stripe and black with a white stripe. Both wires are in the female end of the gray connector (the end that does not go to the transmission). I thought the shiftlock was there so you could shift out of park to get a non-running truck moved. I'm not sure, but I think the shiftlock is a mechanically operated mechanism and doesn't rely on electricity. The problem you've described with wiggling the shifter to get your '94 to turn over sounds exactly like what mine did when the NSS went bad. I confused the problem with the shift lock but actually the problem was further down the line......at the transmission and the NSS. I had success starting the engine by wiggling the shifter a couple of times, but finially the switch went out and no amount of wiggling would get it to turn over. No current will go to the starter if there is a break in the continuity between the black w/red stripe and black w/white stripe wire. I guess I'm not clear on how much of the original harness you still have. If the original harness is pretty much intact (except for the wires that go to the original transmission, black and white) then you will not get power to the starter relay if the bk/red stripe and bk/white stripe wires aren't connected together. Pictures might help.
 
I am sure we are talking about the same thing, the round harness has a black/white wire and a black/red wire and connects to a black wire and white wire that goes to the NSS on the trans. The black/white wire actually originates I guess from the ignition because it comes out of the firewall (you would have to strip your harness to tell) So from my earlier post if the power flows from the black/white wire to the round connector, from there to the NSS back to the round connector and to the black/red wire to the starter. You are saying to jump the black/white wire to the black/red wire, in essence this is what I am doing, when you jump the 2 wires you are making one long black/white wire bypassing the NSS going straight to the starter. What I have is the black/white wire coming out of the firewall, I have removed the rest of the wires since they only go to the NSS which I no longer have. I guess I will trace the black/white wire back into the the car and see where I am loosing power.
Another question, why does this deactivate the cruise control, and is there a way to jump something and make it work without the NSS?
Rusty
 
Rusty,
I follow you now. What you did makes sense to me as long as the black/red goes to the starter. I never traced my wire that far. This safety feature seems more involved to me due to the fact that my cruise no longer works. If I "un-jump" my bk/red to bk/white wires, reconnect the plug, and start the truck in neutral the cruise works. If you figure out a work around for the cruise control please let me know.
 
I found the starter wiring problem, there was an aftermarket alarm on the car when I got it. I didn't have the remote to turn it off so I just cut it out. I didn't think about the fact the ignition would run through it, or at least the starter circuit. The alarm used a harness that was inserted at the ignition switch connector under the steering wheel. The wires I cut from the alarm were yellow and red so I didn't think anything about it until I crawled under and noticed the yellow wire was and extension of the black/white starter wire. I removed the harness and put the factory plugs back together and now I am getting power to the starter. I am obviously bypassing the NSS since I don't have the A442 transmission so I apparently will still have to figure out how to make the cruise work without it? I still haven't figured out the shift lock though? I put in the key, turn it on (engine isn't running yet though) and it won't shift out of park. How does this system work?
Rusty
 
I had this same problem and have yet to solve it but mine is intermittent. I have temporarily solved mine as suggested here......with a carpenters pencil......don't laugh ...it works. Here is a link to describe how the system operates.

http://www.autoshop101.com/forms/h18.pdf

If you'll do a search here for "Shift Lock Problem", you'll find a post by me and some of the responses that helped and described how to run some checks to try and narrow down the problem.

Unfortunately I have a gremlin somewhere.

Good Luck.
 
Thanks, I will read through that, I haven't checked my brake circuit yet, I added hydroboost brakes so I was under there messing with things, the brake lights work so I was assuming that was not the problem but it looks like from briefly looking at the wiring there may be another wire on the pedal that activates the shift lock.
Thanks again
Rusty
 
Back
Top Bottom