Seafoam Wars

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Wondering, has anyone done before and after measurements on say an exhaust analyzer, dynamometer, looked in the cylinders or intake with a fiberoptic borescope,etc, before and after the use of Seafoam? It does look cool, but, has anyone, including the company that makes it, shown any benefit?
 
People have removed intakes before and after treatment. It definately cleans out carbon and varnish.

I started using it with my dad as a kid on the boat, , snowmobile and small engine stuff.

I tore down a dirty mini bike motor looked at it. Reassembled and ran seafoam thru it. Tore it down again. Intake path and head much cleaner.

On the 80 I did all three ways on the can using 3 cans. More pep and smoother idle was the result.

Biggest gains are likely to result from sucking it in a vac line untill it stalls and soaking the intake for a while. Burn it off then repeat.

A simple test would be to wipe an old carboned up spark plug with it.

I like the results.
 
Man, I wish I could walk around in shorts and flipflops at this time of year :flipoff2:

Did you pour it in the PCV hose, or did you let the truck suck it up? Then, did you turn off the engine or did you let it stall?
 
The right way would be the brake booster line and stall it soak for 10min.

Do it on a hot engine. Harder to stall than a cold engine in warm up mode plus hot heads and manifolds clean better.

Treat the oil before a change. Oil flush works as good here dont put seafoam in crankcases so much.

1-2 cans in fuel tank depending on fuel level. Run a whole can thru a vaccum line by stalling soaking and burning it off over and over if it has never been done..

FWIW a friend uses seafoam and or ATF and finally small amount of water thru a tiny vaccum line.

With the seafoam and ATF stall it soak and restart. With the water use a small line and needle nose to control the intake. Just enough H20 to run rough but not stall. When it goes from liquid to vapor it knocks carbon loose on the comb chamber
 
Nice sound track I kind of would have liked to see some of benny hills chicks running around too though....skip the old man however..:D
 
so, does that mean that the Heep is normally a cleaner running engine...? :eek:
 
How much seafoam did you use in the intake and fuel? Notice results?

The instructions calls for 1/3 in the gas tank, 1/3 in the engine and the rest let suck up and stall.

Nice sound track I kind of would have liked to see some of benny hills chicks running around too though....skip the old man however..:D

At least someone appreciates it! I thought it was hilarious. I know some hot chicks walking around instead of my fat butt would have been way better.

so, does that mean that the Heep is normally a cleaner running engine...? :eek:

Who knows. The Jeep actually has 198k on it and the cruiser has 195k. We didnt let the XJ sit with the Seafoam in it quite as long as the cruiser.. so who knows maybe less smoke because of that. We just did this for fun. I noticed no results at all and either did my buddy.
 
FYI, I just used a can through the intake and got a CEL on the next start up. Well see if it comes back. The off idel stumble I had is noticably reduced though. :)
 
I think it is interesting how people automatically assume the smoke is from cleaning off carbon, or any kind of cleaning action whatsoever. From what I've read/seen on BITOG, SeaFoam produces little, if any, observable results. Combine that with some reports of CELs after use, and I'm staying as far away from the stuff as possible.
 
From what I've read/seen on BITOG, SeaFoam produces little, if any, observable results. Combine that with some reports of CELs after use, and I'm staying as far away from the stuff as possible.


I have no idea how it affects an automotive gas engine. But I have used it as a diesel purge, and I have treated the fuel on a honda lawnmower with it. The diesel purge worked great and the engine idled after with much less particulate smoke.

The honda ran like it was new again. It literally was like cleaning the carb. Ran like a dream.The honda was 20 yrs old and was getting stubborn to run. Now it starts first pull.

The stuff does work.

I would never put it in the crank case. It will free up some debris and possibly stick in an oil orfice fawking a bearing I'm afraid.
 
I think it is interesting how people automatically assume the smoke is from cleaning off carbon, or any kind of cleaning action whatsoever. From what I've read/seen on BITOG, SeaFoam produces little, if any, observable results. Combine that with some reports of CELs after use, and I'm staying as far away from the stuff as possible.


Have you read
 
Last edited:
Back
Top Bottom