Running a Saginaw steering conversion without power steering

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Dec 16, 2018
Threads
65
Messages
529
Location
SoCal
Good morning bud, happy Friday everyone. As the title states I have a question about running a Saginaw steering conversion without power steering. This is the 1968 with the GM drivetrain and while I need to check to see how it’s steers with all of the proper components, thanks again to @65swb45 and BT be for the help on this , The steering on the test drives has been light enough that I don’t need the power assist.

I know having power steering can be a help when the four-wheel-drive trails get technical but I don’t envision this rig being exposed to that many conditions.

For mainly around town and fire road use any issues with skipping the power steering? Should I fill the steering box with fluid and then seal it up?

This whole power steering thing is new to me so thank you in advance for being patient with my newbie questions.
 
For mainly around town and fire road use any issues with skipping the power steering?

You will be fine, as long as you aren't running really wide tires. Tall skinny (relatively) tires will be the easiest to steer with manual steering. Fortunately, that is a good combination for Cruisers anyway, and a good look. These are some of the reasons why the 33x10.5x15 tire size is so popular.
 
Saginaw is the brand of box. They make both manual and power gearboxes. A "Saginaw conversion" could mean either, a conversion
with a power assisted gearbox or without. The manual box swap was somewhat common in the 70s and 80s. I've never been asked to do one in the hundred or so conversions I've done. It would be a moot point since you'd be spending a couple grand for little gain
 
Good morning!

@1911 - I’m running 285/70/17. Steering effort without power assist has been fine and I don’t think I’d want the steering to be any lighter.
@lcwizard - the rig came with this set up, it’s plumbed for power steering but the pump etc. did not come with it. I have all that but when I’ve been driving around it’s waiting enough to steer as it is and I’m worried it would be overly touchy with power assist.


416012D0-FC0D-47AD-AE3F-474158F614C8.jpeg
 
Keep in mind there are ways out there to shim and re-valve the pumps to offer LESS assist, so it's not so overboosted. I run a saginaw power steering setup with basically 31x8.5" tires and the boost is almost comical - but boy does it rock offroad.

By the way, doesn't your truck have like...doublers and ultra low gearing and whatnot behind an auto? You know you need to wheel that thing...none of this roads and firetrails nonsense!
 
You don't want to plug the ports but you can run a hose between them with the box full.

@lcwizard - perfect, so I will top it off and then do exactly that. Thank you.

@RWBeringer4x4 - yeah, this thing is pretty built, it’s abilities are going to far exceed that of it’s drivers. I am going to deliberately keep the conditions the rig sees well below the trucks capabilities for this upcoming event just because I need to make sure we finish the darn thing. I’m sure there will be lots and lots of fine-tuning and refinance as I go forward, most of which are going to be in my driving and Offroad skills.

Thank you!
 
You can buy a manual box that will bolt in. You'd have to search late 60's GM cars.
Rather than killing the power entirely you can buy a flow restrictor that will reduce the power and
give more feel to the steering. It replaces the fitting on the back of the pump

 
The PO of my 40 yanked out all the original steering components and installed a Saginaw type setup with the crossmember cutout but sadly, not power assisted! I went to 33x10.5 tires and it made a world of difference.... however, the box could use either a rebuild or replacement but I haven’t been able to find any numbers to identify!
Sorry if this is a hijack but if anyone happens to recognize this box :grinpimp:
5B5F6641-17FE-4A50-96D9-05EEA96F852D.webp

7921ECEC-85E0-48E0-8257-FA17AC04BDF6.webp
 
After reading the above comments about everyone's favorite "mushy" 4 1/4 turn Saginaw gear boxes (with 20 to 1 ratio), some might agree with me that the 3 1/2 turn boxes (with 16 to 1 ratio) have a much better/solid highway feel.
 
@tdskip Here is an article where they did it manually because they did not want to add a bracket to the F engine and it still helped by eliminating sources of tolerance
After speaking with Advance Adapters’ Steve Roberts, we chose a manual Saginaw conversion for our Land Cruiser. Initially we had intended to install power steering, but there is no commercially available power steering pump bracket for the original Toyota F engine in our Land Cruiser.
And before someone gets upset, yes there is a mount that uses the engine mount bolts had they gone that way.
 
The PO of my 40 yanked out all the original steering components and installed a Saginaw type setup with the crossmember cutout but sadly, not power assisted! I went to 33x10.5 tires and it made a world of difference.... however, the box could use either a rebuild or replacement but I haven’t been able to find any numbers to identify!
Sorry if this is a hijack but if anyone happens to recognize this box :grinpimp:
View attachment 2098643
View attachment 2098642
You've got a 4 bolt manual box. The three bolt boxes are more common, even available brand new. I haven't seen the four bolt versions in a while. The three bolt versions will bolt up the the four bolt pattern
 
@Downey - you think the 3.5 turn boxes are better? Everyone else I’ve ever read/talked to says with says those boxes are twitchy/scary on-road. Not saying you’re wrong as I’ve only ever had the 4-turn box, just curious since I’ve always heard the (way harder to find) 4-turn boxes are the way to go...
 
@RWBeringer4x4 - My box is 3.5 and I personally can't imagine wanting to have power assist on it on road. It is a bit heavy if you are at a dead stop but once moving it is light enough.
 
@Downey - you think the 3.5 turn boxes are better? Everyone else I’ve ever read/talked to says with says those boxes are twitchy/scary on-road. Not saying you’re wrong as I’ve only ever had the 4-turn box, just curious since I’ve always heard the (way harder to find) 4-turn boxes are the way to go...


A 4 turn box usually ends up around 3 1/2 on a 40 but it depends on your pitman arm length and box placement. The faster boxes are actually , well, faster so maybe harder to get accustom to. I put a 12:1 , 2 turn box on my 40 and ran over the curb at the first turn I encountered. . That's not nearly as shocking as picking up a used saginaw at a salvage yard, not knowing where it came from, finishing
the job then finding out when you turn the wheel left , the tires go right. Reverse rotation boxes like late 80s camaros index their pitman arms forward, like a 60 0r 80 box. Physically they look the same. I've purposely had one built for a Nissan Hardbody that I did a saginaw steering on. You just have to swap out the guts
 
A 4 turn box usually ends up around 3 1/2 on a 40 but it depends on your pitman arm length and box placement. The faster boxes are actually , well, faster so maybe harder to get accustom to. I put a 12:1 , 2 turn box on my 40 and ran over the curb at the first turn I encountered. . That's not nearly as shocking as picking up a used saginaw at a salvage yard, not knowing where it came from, finishing
the job then finding out when you turn the wheel left , the tires go right. Reverse rotation boxes like late 80s camaros index their pitman arms forward, like a 60 0r 80 box. Physically they look the same. I've purposely had one built for a Nissan Hardbody that I did a saginaw steering on. You just have to swap out the guts

I get a full two turns in both directions lock to lock from center. Even still, I always felt like the turn radius on my truck was massive. I struggle to make turns in an FJ40 that the 80-series in front of me makes.
 
My first Saginaw P.S. conversion used a 4 1/4 turn box, which seems to be the popular choice here on Mud. I then went with the 3 1/2 turn box since it had much better ratios when converting to dual ratio (like I did). Frankly I only saw a very slight difference between the 4 1/4 and 3 1/2 turn boxes, but the 3 1/2 turn had a much better feel of the road. I've never used the 2 turn close ratio boxes found on Corvettes, Trans Ams (GM sport cars), but wished I had a 2 turn box when I once ran a tight multiple hair pin off road obstacle course.
 
I get a full two turns in both directions lock to lock from center. Even still, I always felt like the turn radius on my truck was massive. I struggle to make turns in an FJ40 that the 80-series in front of me makes.
Are you hitting the turn stops on the knuckles at lock?. It makes no sense that the 80 would turn sharper unless your tires are big enough
that the they contact the leaf springs before full lock. The 80 and 40 are both closed knuckles with virtually identical layout. The open knuckle front end like Dana do have a tighter turn radius but all the closed knuckles suffer a little in comparison. Old Danas were closed knuckle. The intro of the open knuckle made for a better turn radius on trucks sporting Danas. First check to see if you're hitting the turn stops and they haven't been turned out to limit the wheels
 
Back
Top Bottom