Reverse Switch access

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Apr 16, 2003
Threads
53
Messages
196
Location
Washington DC
Having a problem with my reverse lights. They are always on. I have searched the forums and it seems like checking the reverse switch is the 1st thing to do. I took off the rubber shifter boots to both sticks. Is there a different shifter boot I need to remove to access the switch?

what am i not seeing...

Thanks

Dave
1974 FJ40
 
Your reverse switch is located towards the rear of your four-speed transmission, on the top of it, and may be very difficult to see by just removing the shift boots...


I have not ever been able to get to one on a 4spd in a pre 1980-40 series this way....


I have always worked from under the truck, between the body, or removed the tunnel.


Good luck!


-Steve
 
Not unless you have a 3" body lift installed....then it would be 'right there'


Grab a light and crawl under there. Look on the top, rear part of the tranny, from the rear of the vehicle. It is going to be very tight/close to the floor of the truck...This is not something that is right out in the open...


Good luck!


-Steve
 
Dave-


It would be best if you go out to your truck with a light, and look for the piece on the top/rear section of the transmission, right in front of where the tcase meets the tranny. It may be in a rubber boot, but there should be two wires comming from it...


Please go look at it, and then you will see how 'easy' it is to access...


Good luck!


-Steve
 
alright... so found the switch, and the access... and it certainly is tight. Next question is.... Is the switch held in by a retaining bolt?

also it seems that my 22mm wrench wasn't big enough. does that sound right? if so, anyone know what size that bolt is?
 
It threads into the rear of the transmission top plate....

May need a 24mm or 15/16" is close too... I have not messed with one in the last couple years...


There is no retaining bolt.


Good luck!


-Steve
 
OK.... have an update... and a question.

it was indeed a 15/16 crowfoot wrench on a 6-inch extender that allowed me access to the backup switch.

the problem i was having was that the lights were always on. When i removed the switch, when the plunger was in the out position the lights were on. When i pressed the plunger in it turned the lights off. is this correct? my intuition would be that when the plunger was out the lights would be off and when the plunger was pressed that they would be on.


so can someone tell me if my switch is working correctly? and that i really have a different problem (reverse wiring somewhere?)

Thanks
 
the later switches in FJ60's are always on unless in reverse, earlier fj40's are on only in reverse.. Hope that little tidbit helps..
 
so is it possible the previous owner (just bought this rig) put an always on switch in it? i guess to answer my own question with PO anything is possible.

so if i understand this correctly i should have a switch that when the plunger is out it is off right?
74 FJ40
 
yep.. When i put the toybox in my 40 i had to use an fj60 switch which is wired backwards.. My stuipd mistake and i now have no reverse lights.. unless i want em always on!
But alas I'd hook up a cont tester first before spending a bunch of time on the project.. does it switch at all in reverse? like the lights go out if in reverse? on in any other gear?
 
good point. i hadn't checked when in reverse.... but i know they are on in every forward gear. i also know they are off when the plunger is pushed in. What i haven't checked is if the plunger is depressed in reverse so the lights go out.
 
i just read the above post and realized how stupid it seems that i haven't checked the lights in reverse.... i guess i got fixated on the fact that the lights were on at ALL other times.
 
Back
Top Bottom